background image

 

 

 

 

DT Research, Inc. 

2000 Concourse Drive, San Jose, CA 95131 http://www.dtresearch.com 
Copyright © 2020, DT Research, Inc. All Rights Reserved. 
 

 

 

 

7

 

 

FCC Regulatory Compliance   

Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.   

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed 

to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, 

if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that 

interference will not occur in a particular installation.   

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one or more of the following measures:   

-- Reorient or relocate the receiving antenna.   

-- Increase the separation between the equipment and receiver.   

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.   

-- Consult the dealer or an experienced radio/TV technician for help. 

 

RF Exposure Compliance   

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.   

The device has been tested for use against the body with 0mm separation in Specific Absorption Rate (SAR) testing.   

User must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with 

any other antenna or transmitter. 

 

Supplier's Declaration of Conformity 

47 CFR § 2.1077 Compliance Information 

Unique Identifier 

Trade Name:                  

,   

Model No.: 

DT

313Y   

Responsible Party – U.S. Contact Information 

 

DT Research, Inc.

 

2000 Concourse Drive, San Jose, CA 95131   

http://www.dtresearch.com   

FCC Compliance Statement 

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation. 
FCC ID Label is in removable battery compartment, it could be easily found by removing the battery cover. 

 

 

 

 

 

Summary of Contents for DT313Y









Reviews: