2
II.
UNPACKING
The packaging is designed to handle normal shipping and handling. Upon receipt of shipment, check for signs of
damage before opening and report all damage to the carrier. All shipments made from DTS are customer
responsibility once they leave our premises.
Before installation is begun it is suggested that a complete inventory be taken to minimize problems or questions
during installation. Additionally, save all packing material until installation is complete in the unlikely event that
a component(s) requires return to the factory. Use the packing slip that came with your unit to verify received
inventory.
The following is a sample packing list for a single projector (platter) system:
•
DTS-6D processor and power cord
•
Timecode Reader Head, 35mm, P/N D600
•
Reader Head Mounting Bracket
•
Timecode Reader Head Interconnect Cable, P/N D435
*
•
Analog Output Cable, P/N 2503-0014-00
**
(same part as logic cable)
•
Digital Output Cable, P/N D713
***
•
Logic breakout board (
as it applies to your cinema processor
)
CP45 uses P/N D716
CP55 uses P/N D565
CP65 uses P/N D564
CP50
/
CP100
/
CP200 use one P/N D567 board and one P/N D711 cable
CP500 uses one P/N D715
UltraStereo uses P/N D571
•
Audio breakout board (
as it applies to your cinema processor
)
CP45/CP65 use P/N D574
CP55 uses P/N D572
CP50
/
CP100
/
CP200 use two P/N D712 cables (
with the D567 board, mentioned above
)
CP500 uses the audio output cable only (
does not use an audio breakout card
)
UltraStereo uses P/N D575
SMART MOD
V
processors use
P/N
D714
interface cable (
no DTS boards
).
SMART MOD
VI
processors use
P/N D706
interface cable (
no DTS boards
)
•
Automation (
logic
) cable, P/N 2503-0014-00
(same part as analog output cable)
•
Installation Hardware
•
Manual
•
DTS trailer (logo) films, two scope and two flat
NOTES
:
*
Timecode cable for two projector (change-over) systems should change to a “Y” cable, P/N D435.. Plus, an additional reader
head, mounting bracket, and hardware should be included, and the DTS-6D should be programmed for change-over operation (see
Section 3.2 for DTS-6D programming details).
**
Analog output cable, P/N 2503-0014-00, is used with cinema processors capable of discrete multi-channel input: Dolby, Kintek,
Pana-Stereo, RGM, Smart, and UltraStereo JS Series.
***
Digital output cable, P/N D713 is available for digital signal processors, models UltraStereo DSP-60S and Cinema Acoustics
CA-CP600.
If any of the items on your packing list cannot be found, contact DTS with the P/N and description of the missing item(s).
Refer to
“
RETURNS
,”
page ii, when sending any product back to DTS.
Summary of Contents for DTS-6D
