background image

fpv

RAcing

Introduction

1

Congratulations on purchasing the DTSQ220 Race QUAD. To ensure your continued enjoyment, 
please take the time to thoroughly read through this operating manual before using. 

Important Notes

Radio Control (R/C) multicopters are not toys. R/C multicopters utilize various high-tech components to 
achieve superior performance. Improper use of this product can result in serious injury or even death. 
Please  read  this  manual  carefully  before  operating,  and  make  sure  to  be  conscious  of  your  own 
personal safety and the safety of others nearby when operation all DTS products. Manufacturer and 
seller assume no liability for the operation or the use of this product. This product is intended for use 
only by adults with experience flying remote control aircraft at legal flying fields. After the sale of this 
product we cannot be held liable over its operation or usage.
As the user of this product, you are solely responsible for operating in a manner that does not in danger 
yourself and others or result in damage to the property of others.

Safety Notes (General)

Fly only in safe areas, away from other people. Do not operate R/C aircraft indoors or within the 
vicinity of homes or crowds of people. R/C aircraft are prone to accidents, failures, and crashes due 
to a variety of reasons including: lack of maintenance, pilot error, and radio interference. Pilots are 
responsible for their actions and damage or injury occurring during the operation or as of a result of 
R/C aircraft models.
Prior to every flight, carefully check all parts such as blades, screws, frame, arms, etc; ensure they 
are firmly secured and show no unusual wears, or unforeseen danger may happen.

Warning Label Legend

Do not attempt under any circumstances.

Mishandling due to failure to follow these instructions may result in serious 
damage or injury.

禁     止

FORBIDDEN

警     告

WARNING

Safety Notes (Battery Installation)

DTS Q-series has a flexible battery mounting system, and uses an industry-standard XT-60(AMASS) 
connector. This allows it to use a wide range of different batteries.

Voltage:

3s (11.1V) pack is recommended. Running 4s (14.8V) is an extremely fast race-quad, which 

can easily get a pilot into trouble.

Capacity:

1000mAh~1500mAh Li-Po battery is recommended.

C Rating:3

0C or above Li-Po battery is recommended.

When installing the selected battery, pay attention to the Center of Gravity mark on the bottom.

Summary of Contents for Q220






























Reviews: