background image

3- MOUNTING THE LAMPS

Warning: Switch off the unit before replacing the lamp.

1) Using a screwdriver, remove the 3 screws X,Y, Z, (photo 1) which fix the lamp holder.

2) Remove the lamp holder assembly and insert the lamp (photo 2).
The lamp used on XR 5  is made in quartz glass and should be handled with care. Always follow the 
instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided 
in the lamp's packaging. The GY9,5  lamp socket is not symmetrical.
DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat 
the procedure.
3) Replace the lamp assembly and tighten the screws X,Y,Z, which were previously removed (photo3).

3.1 Lamp alignment

Attention: we recommend to align the lamp in the optical system  to avoid overheating of the dichroic 
filters and other components inside the unit. 

Alignment is carried out using the 3 adjusters A, B and C.
During this operation you must have a uniform luminosity all around the projected area.

Philips MSD250/2
Power 250W
Luminous flux 18.000 lm
Colour temperature 8.500°K
Lampbase GY9,5
Rated life 3,000 hours

6

Photo 2

Photo 1

Photo 3

Photo 5

ARC 1200

XR 5  WASH

Summary of Contents for XR 5 WASH

























Reviews: