Downloaded from Projector.com
ENGLISH-16
O
O
O
O
P
P
P
P
E
E
E
E
R
R
R
R
A
A
A
A
T
T
T
T
II
II
O
O
O
O
N
N
N
N
S
S
S
S
((
((
c
c
c
c
o
o
o
o
n
n
n
n
tt
tt
ii
ii
n
n
n
n
u
u
u
u
e
e
e
e
d
d
d
d
))
))
No Signal Menu
The same adjustments and settings are available as with the Image and
Options menus when the MENU button is pressed during display of the
“NO INPUT IS DETECTED ON ***” or “SYNC IS OUT OF RANGE
ON ***” message while no signal is received.Select an item with the
and
buttons, and start or stop operation with the
and
buttons.
Table 8. No Signal Menu
VOLUME
BLANK
MIRROR
START UP
MENU COLOR
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
16
Item
Description
VOLUME
Reduce
↔
Increase
• When this function is used, audio input is automatically switched to video. The
audio input can be switched by moving the DISK PAD left and right during the
display of the volume adjustment bar. The volume adjustment bar is displayed by
pressing VOLUME
/
button.
BLANK
Select Blank Screen Color:
Select the color with the
/
button.
• When the blank mode is set with BLANK ON, by absence of a signal, or by
input of a non-standard signal, the image is cleared and the complete screen is
displayed in the selected color.
MIRROR
Select Mirror Status:
Select the mirror status with the
/
button.
START UP
Setup Initial Screen Display:
Select the TURN ON with the
button.
Clear Initial Screen Display:
Select the TURN OFF with the
button.
• Note that if TURN OFF is selected the blank screen is displayed in blue when
there is no signal.
MENU COLOR
Select Menu Background Color:
Select the color with the
/
button.
LANGUAGE
Select Menu Display Language:
Select the language with the
/
button.
AUTO OFF
Set AUTO OFF:
Set 1~99 minutes with the
/
button. The system
automatically enters the standby mode when a signal is not received for
the set time.
Clear AUTO OFF:
Select the STOP (0 min.) with the
button. When
the STOP is selected the system does not enter the standby mode even
if no signal is received.
SYNC ON G
SYNC ON G Valid:
Select the TURN ON with the
button.
SYNC ON G Invalid:
Select the TURN OFF with the
button.
• May not be displayed correctly with some input signals when the SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received,
set the SYNC ON G to invalid, and reconnect the signal.
WHISPER
Set / Crear WHISPER Mode:
Press the
/
button. When the
WHISPER is selected, the WHISPER mode is active. In the WHISPER
mode, acoustic moise level from the unit is reduced, and brightness
level on screen is a little lower.
01CP-S370W 02.1.15 9:07 AM ページ 16
Summary of Contents for 28A8052
