background image

Twin Twist Soft Serve Freezer Model 957RMT

184957   

 

 

 

    

 

 

 

 

 

 

 

             15

Operator Controls 

(continued)

2.  Mix Transfer System (MTS) Switch

This three-position switch controls the 

operation of the MTS located in the 

refrigerated mix storage cabinet.
A.  

“MIX ON”

 (Left Position) - Use this 

position when the freezer is in the 

normal operating mode and/or when 

the product is being removed from the 

cylinder.

B.    “OFF” (Center Position) - In this 

position the MTS will not operate.

3.  Cabinet Switch

This two-position switch controls the 

cabinet refrigeration.

NOTE: 

 The cabinet door must be closed 

for cabinet refrigeration to operate.
 

 

A. 

“ON” (Left Position) - 

The cabinet thermostat controls the 

system refrigeration to maintain a 

temperature of 36º - 40ºF (2º- 4ºC) 

in the storage cabinet. This position 

must be used when mix is in the 

storage cabinet.

B.  “OFF” (Right Position) - The cabinet 

will not be refrigerated in the “OFF” 

position, unless either selector switch 

is in the “ON” position.

NOTE: 

The cabinet is automatically “ON” 

when either selector switch is in the 

“AUTO” position.

4. Timer

This control will bypass the thermostat, 

forcing the compressor and beater motor 

to run for approximately 3 minutes. 

Use the timer for quick start-ups or fast 

recovery when dispensing large portions.

       IMPORTANT:

 

Excessive use of the timer causes 

freeze-up and damage to the freezer.

5.  Reset - Overload

This control protects the beater motor 

against failure from an overload condition 

by automatically shutting down the 

freezer. To restart properly, turn the 

selector switch to “OFF”, wait 2-3 minutes, 

then depress the red reset button and turn 

the selector switch back to the “AUTO” or 

CLEAN” position.

     IMPORTANT:

If the overload trips frequently, your 

freezer should be checked for proper 

product temperature, overrun and 

voltage. Contact H.C. Duke & Son, 

Inc. or your local refrigeration service 

company.

Summary of Contents for DQ 957RMT




















































































Reviews: