background image

3

Installation and Operation of: Front Line Merchandiser

In addition to the warnings and cautions in this manual, use the following guidelines for 

safe operation of the unit.

•  Read all instructions before using equipment.
•  For your safety, the equipment is furnished with a properly grounded cord connector. Do  

    not attempt to remove or disconnect the grounded connector.
•  Install or locate the equipment only for its intended use as described in this manual. 
•  Do not use corrosive chemicals in this equipment.
•  Do not use caustic cleaners, acids, ammonia products or abrasive cleaners or abrasive    

  cloths. These can damage the stainless steel and plastic surfaces.
•  Do not operate this equipment if it has a damaged cord or plug, if it is not working  

 

  properly, or if it has been damaged or dropped.
•  This equipment shall be serviced by qualified personnel only. Contact the nearest Duke 
  authorized service facility for adjustment or repair.
•  Do not block or cover any openings on the unit.
•  Do not immerse cord or plug in water.
•  Keep cord away from heated surfaces.
•  Do not allow cord to hang over edge of table or counter.
•  If the supply cord is damaged, it must be replaced by a special cord assembly available    

  from Duke Manufacturing Co. or its service agent.

  Note: Refer to the specifications data plate when ordering or replacing a cord set.
The following warnings and cautions appear throughout this manual and shall be 

carefully observed.

•  Turn the unit off, disconnect the power source and allow unit to cool down before   

 

  performing any service or maintenance on the unit.
•  The procedures in this manual may include the use of chemical products. You must read   

  the Material Safety Data Sheets before using any of these products. 
•  The unit shall be grounded according to local electrical codes to prevent the possibility    

  of electrical shock. It requires a grounded receptacle with dedicated electrical lines,  

 

  protected by fuses or circuit breaker of the proper rating, in accordance with all    

 

  applicable regulations.
•  Disposal of the unit must be in accordance with local environmental codes and/or any    

  other applicable codes.
•  This appliance is not intended for use by persons (including children) with reduced  

 

  physical, sensory or mental capabilities, or lack of experience and knowledge, unless  

 

  they have been given supervision or instruction concerning use of the appliance by a    

  person responsible for their safety.

•  CAUTION

: Never use a high-pressure water wash for this cleaning procedure as water    

  can damage electrical components

Summary of Contents for FLM200









Reviews: