background image

2

Introduction

Acquisition & Warranty

On delivery of your new Duncan Maxi-Till Cultivator, please
check that the machine is not damaged. In cases of shipping
damage, please ask your dealer to arrange for the appropriate
claim to be lodged immediately. Assemble any parts supplied
loose and inspect your machine with the aid of this manual to
familiarise yourself with its features. If you have any queries
ask your dealer straight away. The machine is covered by our
12 month warranty on faulty parts, subject to normal use.

Record below the serial number of your machine and keep
it in a secure place to help trace the machine and assist
us when you order parts.

The Owner’s Manual

Your new Duncan Maxi-Till will give long and efficient service if
given normal care and operated properly. 

This owner’s manual is provided so that you can become
thoroughly familiar with the design of the machine and to
furnish information on correct operation, adjustment and
maintenance. 

Only persons well acquainted with these

guidelines should be allowed to use the equipment.

A separate illustrated parts section has been provided so that if
any parts are required your dealer will be able to supply them
by reference to part numbers.

The manual is considered as part of your machine and must
remain with the machine when it is sold.

Right and left hand references in this manual are
determined by standing behind the machine and facing in
the direction of travel.

Model:

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Serial No:

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Owner:

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Delivery Date:

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Dealer:

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Disclaimer

Every effort has been made to 
ensure that the information in this 
manual was accurate and up to 
date at the time of going to press.  
Clough Agriculture reserves the 
right to make subsequent changes 
to the machine, where necessary, 
without notification.

The Company will not be 
responsible for any damage or 
consequential loss arising out of 
misinterpretation or failure to follow 
recommended procedures. Nor will 
it be liable for any damage caused 
by or arising out of modification or 
misuse of its product.

The owner has a responsibility to 
protect himself and others by 
observing all safety information 
and by ensuring all operators are 
well acquainted with the safety 
information, trained in the 
correct use of the machine and 
applying safe work practices.

Summary of Contents for Maxi-Till 920





















Reviews: