DTSL3/FR MKII USER’S MANUAL
17
Chapter
Chapter
Chapter
Chapter 6
6
6
6 OPERATION
OPERATION
OPERATION
OPERATION
Only
Only
Only
Only skilled
skilled
skilled
skilled and
and
and
and having
having
having
having been
been
been
been trained
trained
trained
trained personnel
personnel
personnel
personnel is
is
is
is allowed
allowed
allowed
allowed to
to
to
to perform
perform
perform
perform the
the
the
the operations.
operations.
operations.
operations. Check
Check
Check
Check proceedings
proceedings
proceedings
proceedings as
as
as
as following.
following.
following.
following.
Operation
Operation
Operation
Operation Notices:
Notices:
Notices:
Notices:
-Clear obstacles around the lift before operation.
-During lifting or lowering, no person is allowed to stand near the two sides and beneath the machine, and no person is allowed on
the two platforms.
-Avoid to lifting over weight vehicles or other goods.
-When lifting vehicle, the chassis of the vehicle should be filled up with rubber cushion.
-Pay attention to the synchronization of the lifting and lowering. If any abnormal is found, stop the machine timely, check and
remove the trouble.
-When the equipment is not used for a long time or over night, the machine should be lowered to the lowest position on ground, and
remove vehicle, and cut off power supply.
Instructions
Instructions
Instructions
Instructions on
on
on
on electric
electric
electric
electric operation:
operation:
operation:
operation: (see
(see
(see
(see the
the
the
the operation
operation
operation
operation panel
panel
panel
panel picture
picture
picture
picture 24
24
24
24))))
LIFTING:
LIFTING:
LIFTING:
LIFTING:
-Press ‘
UP
UP
UP
UP
’ button, the platforms go up. And the platforms will stop lifting when reach the up limit switch.
-Release ‘
UP
UP
UP
UP
’ button, the oil pump will stop immediately. And the platforms stops lifting.
LOWERING
LOWERING
LOWERING
LOWERING::::
-Press "
DOWN
DOWN
DOWN
DOWN
" button, the platforms descend.
-And the platforms will stop lowering automatically around 200~300mm height when reach the lower limit switch. Release
"
DOWN
DOWN
DOWN
DOWN
" button, then press "
SECOND
SECOND
SECOND
SECOND DOWN
DOWN
DOWN
DOWN
" button to let platforms go down to the lowest position.
EMERGENCY
EMERGENCY
EMERGENCY
EMERGENCY STOP:
STOP:
STOP:
STOP:
When the machine has abnormal during car maintenance, press "
EMERGENCY
EMERGENCY
EMERGENCY
EMERGENCY STOP
STOP
STOP
STOP
" button and lock, to cut off all the operation
circuit, so other operation can not be work.
NOT
NOT
NOT
NOT IN-PHASE
IN-PHASE
IN-PHASE
IN-PHASE STOP
STOP
STOP
STOP MACHINE:
MACHINE:
MACHINE:
MACHINE:
When two platforms are not at the same height during lifting and lowering operations, photo-electricity leveling equipment will stop
working immediately. According to the following process to adjust the platform level, only after two platforms are at the same height
can put them into use.
Oil
Oil
Oil
Oil make-up
make-up
make-up
make-up “
“
“
“adjust
adjust
adjust
adjust”
”
”
” operation
operation
operation
operation (normal
(normal
(normal
(normal service
service
service
service period):
period):
period):
period):
After completion of machine installation and adjustment in the application process, the right platform
is lower than the left one because of air in the oil cylinder not being excluded completely normal
looses or leakage of the hydraulic oil.
When conducting oil make-up operation, the platforms must not load.
Adjustment process is as approach ‘5’ and ‘6’ of ‘Oil make-up adjustment’.
EMERGENCY
EMERGENCY
EMERGENCY
EMERGENCY MANUAL
MANUAL
MANUAL
MANUAL OPERATION
OPERATION
OPERATION
OPERATION FOR
FOR
FOR
FOR LOWERING
LOWERING
LOWERING
LOWERING (POWER
(POWER
(POWER
(POWER FAILURE):
FAILURE):
FAILURE):
FAILURE):
When lowering through manual operation, should observe the condition of platform at
Any
time because there is vehicle on the platforms. If there is something abnormal, screw
Picture
Picture
Picture
Picture 24
24
24
24 (control
(control
(control
(control panel)
panel)
panel)
panel)
Picture 25
