background image

2

Introduction and Warranty

                 Cordless Roofing 
Nailer Operating Manual

1. READ THE MANUAL FROM COVER TO COVER
    BEFORE USING THE TOOL.

2. FOLLOW ALL INSTRUCTIONS IN THE MANUAL.

For the nearest 

Duo-Fast

®

 representative call 1-888-

631-2020.

Name

Address

p

i

Z

 

 

 

 

 

e

t

a

t

S

y

t

i

C

Telephone  Number

Duo-Fast

®

 Cordless Warranty and Limitations

Duo-Fast

®

 warranties that new Cordless power fastening tools,

parts and accessories will be free from defects in material and
workmanship for the period shown below, after the date of
delivery to the original user.

ONE-YEAR LIMITED WARRANTY

A one-year warranty will apply to all parts, except those listed
below as normal wearing parts, or parts which are specifically
covered by an extended warranty.

FIVE-YEAR EXTENDED LIMITED WARRANTY

A five-year warranty will apply to all molded nylon parts:

Cap and Grille

Handle Halves and Actuator

Trigger

90-DAY LIMITED WARRANTY

A 90-day warranty applies to the following parts, which are
considered normal wear parts:

Bumper

Driver Blades

Seal Rings

WARRANTY STATEMENT

This warranty is limited to tools sold and service requested in the
United States. To obtain information on warranty service in the
United States, refer to the Service Center listing that was provided
with your tool.

Duo-Fast’s sole liability hereunder will be to replace any part or accessory
which proves to be defective within the specific time period. Any replacement
part or accessory provided in accordance with this warranty will carry a
warranty for the balance of the period of warranty applicable to the part it
replaces. This warranty does not apply to part replacement required due
to normal wear.

This warranty is void on any tool which has been subjected to misuse,
abuse, accidental or intentional damage, use with fasteners, fuel, batteries,
or  battery chargers not meeting  Duo-Fast

®

 specification, size, or quality,

improperly maintained, repaired with other than genuine Duo-Fast

®

replacement parts, damaged in transit or handling, or which, in Duo-Fast’s
opinion, has been altered or repaired in a way that affects or detracts from
the performance of the tool.

Duo-Fast

®

 MAKES NO WARRANTY, EXPRESSED OR IMPLIED,

RELATING TO MERCHANTABILITY, FITNESS, OR OTHERWISE,
EXCEPT AS STATED ABOVE, and Duo-Fast's liability AS STATED  ABOVE
AND AS ASSUMED ABOVE is in lieu of all other warranties arising out of,
or in connection with, the use and performance of the tool, except to the
extent other wise provided by applicable law. Duo-Fast

®

 SHALL IN NO

EVENT BE LIABLE  FOR  ANY DIRECT, INDIRECT, OR CONSEQUENTIAL

DAMAGES, INCLUDING, BUT NOT LIMITED TO, DAMAGES WHICH
MAY ARISE FROM LOSS OF ANTICIPATED PROFITS OR PRODUC-
TION, SPOILAGE OF MATERIALS, INCREASED COST OF OERA-
TION, OR OTHERWISE.

Duo-Fast

®

 reserves the right to change specifications, equipment or designs.

This manual is intended to acquaint you with the 
Duo-Fast

®

 Cordless Roofing Nailer. Unlike other power 

fastening tools, the Cordless Roofing Nailer is powered 
by an internal combustion linear motor. In simpler terms, 
your Cordless Roofing Nailer is powered by a motor 
similar to the one that powers an automobile. The Cord-
less Roofing Nailer ignites a fuel and air mixture to 
produce the energy to drive the motor, which in turn 
drives the fastener. The Cordless Roofing Nailer is totally 
self-contained. It carries its own fuel supply and battery, 
along with a supply of fasteners. For ease of use, this 
manual is divided into sections (see Contents). Each 
section of the manual is written with you,the  tool  opera-
tor, in mind. We have left out many of the technical 
terms so that you can easily understand how to get  the 
maximum performance from your Cordless Roofing 
Nailer,  and how to avoid damaging the tool or injuring 
yourself. But, to accomplish this, we need you to do two 
things:

The Cordless Roofing Nailer should be handled like 
other  power fastening tools that you use. Like most tools, 
when used improperly injury could result . If you are 
going to allow others to use the Cordless  Roofing-
Nailer,  it  is  your  responsibility to make sure that they also 
read and comply with the instructions in this manual 
before attempting to operate the tool. Should  you  have 
questions about the Cordless R o o f i n g Nailer, or wish 
to obtain additional copies of this manual, please contact 
your 

Duo-Fast

®

 

representative. The space below is pro-

vided so that you may record your representative's 
name, address, and telephone number.

Summary of Contents for DFCR175C



















Reviews: