background image

23

22

7. Appendix

7.1 Caution & Warning

1.  The unit can only be repaired by qualified installer centre personnel or an authorised dealer. (for 

Europe market)

2.  This  appliance  is  not  intended  for  use  by  persons  (including  children)  with  reduced  physical 

sensory or mental capabilities, or lack of experience and knowledge, unless they have been 

given supervision or instruction concerning use of the appliance by a person responsible for their 

safety. (for Europe market) Children should be supervised to ensure that they do not play with 

the appliance.

3.  Please make sure that the unit and power connection have good earthing, otherwise may cause 

electrical shock.

4.  If the supply cord is damaged, it must be replaced by the manufacturer or our service agent or 

similarly qualified person in order to avoid a hazard.

5  The unit CANNOT be installed near the flammable gas. Once there is any leakage of the gas, 

fire can be occur.

6.  Make sure that there is circuit breaker for the unit, lack of circuit breaker can lead to electrical 

shock or fire.

7.  The heat pump located inside the unit is equipped with an over-load protection system. It does 

not allow for the unit to start for at least 3 minutes from a previous stoppage.

8.  The unit can only be repaired by the qualified personnel of an installer center or an authorized 

dealer. (for North America market)

9.  Installation must be performed in accordance with the NEC/CEC by authorized person only.

  (for North America market)

10. USE SUPPLY WIRES SUITABLE FOR 75°C.

11. Caution: Single wall heat exchanger, not suitable for potable water connection.

7.2 Supply cable specifications

1.  

Single phase unit

2. 

Three phase unit

Summary of Contents for DURAPRO-12















Reviews: