Eye and Breathing Protection
The sanding process will create dust and other airborne particles. There is no dust
extraction function on this machine so it is essential that approved eye and breathing
protection is worn.
Noise and Ear Protection
Depending on the material being worked on and the type of sanding disc used, noise
levels may cause hearing damage including temporary or even permanent hearing loss.
It is recommended that Ear Protection is worn at all times when using the sander.
Repetitive Strain Injury (RSI)
All products of this nature can cause RSI if used for long period, particulary in an
awkward operating position. Adequate rest periods and working conditions should be
considered for prolonged use.
General Safety Information
1
Ensure the sanding pad is equal to or greater than 120% of the stated RPM of the
sander.
2
Keep the workplace clean and tidy.
3
Use the tool in a well ventilated area.
4
Air hoses can present a trip hazard, always keep hoses in a way that minimises trip
hazards.
5
DO NOT hold the workpiece by hand, always make sure the workpiece is clamped
securely.
6
Keep all flammable and combustible materials away from the work area.
7
Children and other unauthorised persons should be kept away from the work area.
8
NEVER use the sander whilst the floor underfoot is wet or slippery.
9
NEVER use the sander when standing on an unstable surface.
10
Keep the sander out of reach of children.
11
Analyse the material you are sanding. Be aware of the dangers of sanding lead based
paints. Historically, paint contained lead and sanding such paint will cause toxic dust. If
you suspect that lead could be in the paint the following actions must be observed;
- Alert any other persons in the nearby and keep them away from the working
area.
- Use specific air fed respirator, PE coated coveralls and latex gloves.
- Dispose of any dust and paint waste correctly and thoroughly clean the
workpiece and working area after the sanding has finished.
12
NEVER attempt to sand materials containing asbestos.
13
VIBRATION. Hand held air tools may produce vibration. Vibration from sanders can
cause disease. The use of gloves will help reduce the risk and can help prevent injury.
14
Disconnect the air supply before changing disc or pad.
15
Ensure the sander has stopped rotating before putting it down or handling the pad or
disc.
16
NEVER carry the sander by the air hose.
17
NEVER point the sander at other persons.
18
NEVER operate the sander whilst under the influence or drugs, alcohol or intoxicating
medication.
19
Check you have no loose clothing, hair, jewellery or any other items of a personal nature
that might become entangled with the rotating parts.
20
Check you have a maximum inlet air pressure of 90PSI/6.3BAR.
PLEASE KEEP THIS MANUAL SAFE FOR FUTURE REFERENCE
Duren Tools
T: 01582 484875 E: sales@duren.co.uk
www.duren.co.uk
625624_Product Instructions 27/03/2014 08:30 Page 3
Eye and Breathing Protection
The sanding process will create dust and other airborne particles. There is no dust
extraction function on this machine so it is essential that approved eye and breathing
protection is worn.
Noise and Ear Protection
Depending on the material being worked on and the type of sanding disc used, noise
levels may cause hearing damage including temporary or even permanent hearing loss.
It is recommended that Ear Protection is worn at all times when using the sander.
Repetitive Strain Injury (RSI)
All products of this nature can cause RSI if used for long period, particulary in an
awkward operating position. Adequate rest periods and working conditions should be
considered for prolonged use.
General Safety Information
1
Ensure the sanding pad is equal to or greater than 120% of the stated RPM of the
sander.
2
Keep the workplace clean and tidy.
3
Use the tool in a well ventilated area.
4
Air hoses can present a trip hazard, always keep hoses in a way that minimises trip
hazards.
5
DO NOT hold the workpiece by hand, always make sure the workpiece is clamped
securely.
6
Keep all flammable and combustible materials away from the work area.
7
Children and other unauthorised persons should be kept away from the work area.
8
NEVER use the sander whilst the floor underfoot is wet or slippery.
9
NEVER use the sander when standing on an unstable surface.
10
Keep the sander out of reach of children.
11
Analyse the material you are sanding. Be aware of the dangers of sanding lead based
paints. Historically, paint contained lead and sanding such paint will cause toxic dust. If
you suspect that lead could be in the paint the following actions must be observed;
- Alert any other persons in the nearby and keep them away from the working
area.
- Use specific air fed respirator, PE coated coveralls and latex gloves.
- Dispose of any dust and paint waste correctly and thoroughly clean the
workpiece and working area after the sanding has finished.
12
NEVER attempt to sand materials containing asbestos.
13
VIBRATION. Hand held air tools may produce vibration. Vibration from sanders can
cause disease. The use of gloves will help reduce the risk and can help prevent injury.
14
Disconnect the air supply before changing disc or pad.
15
Ensure the sander has stopped rotating before putting it down or handling the pad or
disc.
16
NEVER carry the sander by the air hose.
17
NEVER point the sander at other persons.
18
NEVER operate the sander whilst under the influence or drugs, alcohol or intoxicating
medication.
19
Check you have no loose clothing, hair, jewellery or any other items of a personal nature
that might become entangled with the rotating parts.
20
Check you have a maximum inlet air pressure of 90PSI/6.3BAR.
PLEASE KEEP THIS MANUAL SAFE FOR FUTURE REFERENCE
Duren Tools
T: 01582 484875 E: sales@duren.co.uk
www.duren.co.uk
625624_Product Instructions 27/03/2014 08:30 Page 3
PLEASE KEEP THIS MANUAL SAFE FOR FUTURE REFERENCE
Duren Tools
T: 01582 484875 E: sales@duren.co.uk
www.duren.co.uk
4
It is strongly advised that you always use a Whip Hose/Leader Hose in combination with
Quick Release Couplings. See
Fig. 2
for recommended setup.
5
Water in the air supply will cause the internal bearing of the tool to rust and eventually
seize.
6
Make sure that your airline is free from water at all times.
7
Always select the correct sanding disc grit for the job.
Tools Included with your Sander
1 x High Flow Male Air Fitting
Maintenance
1
If the air supply is not lubricated sufficiently it will be necessary to lubricate the tool
directly. This can be done by disconnecting the air hose and pouring in 5ml of air tool oil
into the Air Inlet. Read safety data sheet or instructions on use of oil to ensure safe
usage. These can be obtained from your supplier.
2
Replace worn or damaged parts using genuine parts only.
3
Store tool in a dry area, do not allow tool to be immerse in water or used/stored in wet
conditions.
625624_Product Instructions 27/03/2014 08:30 Page 5
PLEASE KEEP THIS MANUAL SAFE FOR FUTURE REFERENCE
Duren Tools
T: 01582 484875 E: sales@duren.co.uk
www.duren.co.uk
4
It is strongly advised that you always use a Whip Hose/Leader Hose in combination with
Quick Release Couplings. See
Fig. 2
for recommended setup.
5
Water in the air supply will cause the internal bearing of the tool to rust and eventually
seize.
6
Make sure that your airline is free from water at all times.
7
Always select the correct sanding disc grit for the job.
Tools Included with your Sander
1 x High Flow Male Air Fitting
Maintenance
1
If the air supply is not lubricated sufficiently it will be necessary to lubricate the tool
directly. This can be done by disconnecting the air hose and pouring in 5ml of air tool oil
into the Air Inlet. Read safety data sheet or instructions on use of oil to ensure safe
usage. These can be obtained from your supplier.
2
Replace worn or damaged parts using genuine parts only.
3
Store tool in a dry area, do not allow tool to be immerse in water or used/stored in wet
conditions.
625624_Product Instructions 27/03/2014 08:30 Page 5
PLEASE KEEP THIS MANUAL SAFE FOR FUTURE REFERENCE
Duren Tools
T: 01582 484875 E: sales@duren.co.uk
www.duren.co.uk
4
It is strongly advised that you always use a Whip Hose/Leader Hose in combination with
Quick Release Couplings. See
Fig. 2
for recommended setup.
5
Water in the air supply will cause the internal bearing of the tool to rust and eventually
seize.
6
Make sure that your airline is free from water at all times.
7
Always select the correct sanding disc grit for the job.
Tools Included with your Sander
1 x High Flow Male Air Fitting
Maintenance
1
If the air supply is not lubricated sufficiently it will be necessary to lubricate the tool
directly. This can be done by disconnecting the air hose and pouring in 5ml of air tool oil
into the Air Inlet. Read safety data sheet or instructions on use of oil to ensure safe
usage. These can be obtained from your supplier.
2
Replace worn or damaged parts using genuine parts only.
3
Store tool in a dry area, do not allow tool to be immerse in water or used/stored in wet
conditions.
625624_Product Instructions 27/03/2014 08:30 Page 5
