PLEASE KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE
Duren Tools
T: 01582 484875 E: sales@duren.co.uk
www.duren.co.uk
Declaration of Conformity
We declare that the equipment detail below, to the best of our knowledge and ability, complies with the following
Directives.
2006/95/EC:
Low Voltage Directive
2006/42/EC:
Machinery Directive
2011/65/EU:
Restriction of Hazardous Substances (RoHS 2)
2004/108/EC:
EMC Directive
2002/96/EC:
Waste Electrical & Electronic Equipment (WEEE)
2011/65/EU:
Restriction of the Use of certain Hazardous Substances in Electrical and Electronic Equipment (RoHS)
Equipment Description
Electric HVLP Turbine Spraygun
Part Code
321240
Distributed in the EU by
Duren Tools, a wholly owned subsidiary of Fast Mover Tools
Address
Unit 1 Frenchs Avenue, Dunstable, Bedfordshire, LU6 1BH, United Kingdom
The following Transposed Harmonised Standards have been applied in the
design and construction of this equipment:
EN 55014-1:2006
Electromagnetic compatibility. Requirements for household appliances, electric tools and similar apparatus Emission
EN 55014-2:1997+A1
Electromagnetic compatibility. Requirements for household appliances, electric tools and similar apparatus Immunity. Product
family standard
EN 50144-1:1998+A1+A2
Safety of hand-held electric motor operated tools General requirements
EN 50144-2-7:2000
Safety of hand-held electric motor operated tools Particular requirements for spray guns
EN 61000-3-2:2006
Electromagnetic compatibility (EMC) Limits. Limits for harmonic current emissions (equipment input current up
to and including 16 A per phase)
EN 61000-3-3:1995+A1+A2
Electromagnetic compatibility (EMC) Limits. Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage
supply systems, for equipment with rated current ≤ 16 A per phase and not subject to conditional connection
The manufacturer and the distributor, stated above, hold the Technical Construction File for this equipment.
Signed on behalf of the distributor
(the responsible person)
…………………………………………
Name:
Brian Moffitt
Position:
Director
Date and Place:
15/04/2014, Dunstable, UK
Warranty
We hope that you will be very happy with your purchase. If you do have a problem with your tool, you have the
added peace of mind of a 6 month warranty, which comes into date from the date of purchase (proof of purchase
required).
Scope of Warranty
- The warranty will cover you from all faults cause by defective components or poor workmanship.
- Tools sent outside the EU are not covered by this warranty.
- Product must be returned to us, the warranty does not cover cost of carriage.
- If the product is no longer in manufacture, it will be replaced with a tool of equivalent or higher specification.
What is not covered
- Normal wear and tear caused by use in accordance with the operating instructions.
- Replacement of any provided accessories, such as, Airline Connections, Air Fittings, Spanners, etc and nozzles
and air caps.
- Accidental damage, faults caused by negligent use or care, neglect, misuse or careless operation, handling and
storage of the product.
- Modification of, or change of, any part of this product in any way.
- Faults caused by use of non compatible accessories.
- Tool seizure caused by insufficient oiling.
- Faults caused by incorrect installation.
- Repairs or alterations carried out by non-approved parties.
- Traces of water,dust or rust inside tool - this shows that a properly working filter has not been used.
Validity
- This warranty is valid for 6 months after date of purchase.
- Warranty is rendered invalid if;
- Tool is taken apart for any reason without our consent.
- The points in the Electrical and General Safety Instructions are not observed.
- A warranty claim will not be accepted without an official proof of purchase from your supplier.
