Duren 321240 Instruction Manual Download

Page: 8 / 12

321240
Instruction Manual

Duren Tools

T: 01582 484875 E: sales@duren.co.uk

www.duren.co.uk

Ref.

Code

Description

321240/1 Power cable with plug

321240/2 Cord sleeve

321240/3 Filter cover

321240/4 Filter

321240/5 Left housing

321240/6 Paint reservoir holder

321240/7 Capacitance 0.22uF

321240/8 Switch

321240/9 4.8 Spring anchor 4.8

321240/10 350W Motor sealing ring 350W

321240/11 Air flow pipe connector

321240/12 Motor

（

350W

）

321240/13 Right housing

321240/14 Screw ST4X16

321240/15 Wirefixed board

321240/16 Screw ST2.9X14

321240/17 Short tube connector

321240/18 Bellows

321240/19 Long tube connector

321240/20 Nameplate

Parts Diagram

Refer to your local dealer about the supply of spare parts. Diagram for qualified service technician only. Only
basic maintenance covered elsewhere in this manual is allowable under the terms of the warranty.

Summary of Contents for 321240













Search results

Summary of Contents for 321240

Reviews:

Related manuals for 321240

Brands by name

Popular brands

Duren 321240, Instruction Manual

Search results

Summary of Contents for 321240

Reviews:

Related manuals for 321240

Brands by name

Popular brands