LED High Intensity Warning Light
Part 0-441-40
0-441-40-LEAF
www.durite.co.uk
WARNINGS
Before using this unit please read these instructions carefully. Take special care to follow the warnings
and safety gestions listed below. Keep these instructions for future reference.
SAFETY WARNING
1.
Proper installation of this product requires the installer to have a good understanding of automotive
electronics, sys-tems and procedures.
2.
If mounting this product requires drilling holes, the installer MUST be sure that no vehicle compo-
nents or other vital parts could be damaged by the drilling process. Check both sides of the mounting
surface before drilling begins. Also de-burr the holes and remove any metal shards or remnants.
3.
Do not install this product or route any wires in the deployment area of your air bag. Equipment
mounted or located in the air bag deployment area will damage or reduce the effectiveness of the air
bag, or become a projectile that could cause serious personal injury or death. Refer to your vehicle own-
er’s manual for the air bag deployment area. The User/Installer assumes full responsibility to determine
proper mounting location, based on providing ultimate safety to all passengers inside the vehicle.
4.
Do not attempt to activate or control this device in a hazardous driving situation.
5.
This product contains either strobe light(s), halogen light(s), high-intensity LEDs or a combination
of these lights. Do not stare directly into these lights. Momentary blindness and/or eye damage could
result.
6.
Use only soap and water to clean the outer lens. Use of other chemicals could result in premature lens
not use a pressure washer to clean this product.
7.
It is recommended that these instructions be stored in a safe place and referred to when performing
maintenance and/or reinstallation of this product.
!" #
be made. The recommended procedure requires the product ground wire to be connected directly to the
NEGATIVE (-) battery post.
8. All connections must use waterproof connectors and any unconnected wires must be sealed to prevent
water ingress via the wire core, failure to do this may result in premature failure and invalidate the
warranty.
0-441-40-LEAF
www.durite.co.uk
MOUNTING
1. Switch Patterns: (Yellow wires touch Red wires)
$ % & '
With the LED Light Heads switched on, momentarily apply + VDC to YELLOW wires for less than 1 sec-
ond and release
To reset:
With the LED Light Heads switched on, quickly apply three times + VDC to YELLOW wires and release.
LED Light Head will reset to the factory default pattern (Pattern # 0, Random)
2. Synchronization: (More than 2 sets of LED Light Heads)
First, connect YELLOW wires of all heads together, quickly apply three times + VDC to YELLOW wires and
release for Pattern # 0, Random.
Secondly, momentarily apply + VDC to YELLOW wires to for less than 1 second and release for Pattern #
1, then the synchronization will be functioned.
3. Alternating or Simultaneous Flash: (More than 2 sets of LED Light Heads)
Under Synchronization, connect WHITE wire of LED Light Head 1 to Red wires of all other LED Light
Heads; LED Light Head 1 will alternate with other LED Light Heads.
89$< = > =# < 9 = & ?
&
4. Flash Patterns: 20 selectable strobe patterns:
FLASH PATTERNS
1. Place the unit against the mounting surface.
@ J = Q X Q
damaged by the drilling process.
3. Using a bit size for a no. 304 metal screw, drill two mounting holes, a 0.5” diameter. Wire passage
hole(s) must also be drilled. Thouroughly de-burr all hole(s).
4. Pass the wires through the hole(s) in the gasket and through the wire passage hole(s) in the mount-
ing surface. Fix the light head to the mounting surface.
CONTENTS
1 x 0-441-40 LED Light Head
1 x Gasket
1 x #304 mounting screws (3 x 7mm)
1 x Installation and Operating Instructions
