A.
If the shoe plate is too long to fit atop the shroud,
remove the metal plate on the front of the shroud by
removing two screws.
Position the saw as far back on the shroud as it will
sit. Use the included zip tie to fasten the saw’s depth
guide arm to the hose port of the shroud to restrict the
saw from moving forward. Position the saw against
the left wall and continue with step 4 of installation.
B.
If the shoe plate is too short and causes blade
interference, simply insert the provided spacer
between the front metal plate and the saw. Peel away
paper backing from adhesive to join to shroud body.
INSTALLATION TROUBLESHOOTING:
OPTIONAL:
Some materials may produce larger particles
when cut that will follow the blade to, and be
ejected from the back opening of the blade
guard. To collect this debris, attach the optional
collection shield to the rear shield mount at the
back of the blade opening in the shroud just as
the primary dust shield is attached to the front.
Continue with basic installation.
Finally, position and form the rear shield around
the outer edge of the saw’s upper blade guard so
that it catches dust that is ejected from the guard.
4.
Firmly fasten both cinching straps
around the shoe plate of the saw. Keep
the buckle anchored to the edge of the
shoe plate, as shown.
2.
UNPLUG saw. Open the two hook-and-loop
cinch straps and, with the saw at minimum
cutting depth, place the saw on top of the
shroud. The front rubber dust shield should
fit inside the upper blade guard of the saw.
5.
Ensure the front rubber dust shield is
properly positioned within both the upper
blade guard of the saw and the blade
opening in the shroud. The shield should
form a “C” channel in front of the blade.
The blade should NOT contact the rubber
shield or any part of the shroud.
INSTALLATION:
3.
Position the saw flush against both the left
and front walls of the shroud.
6.
Hose cuff provided fits standard 1.5”
vacuum hoses. Attach directly to the
outside of the shroud’s hose port.
A vacuum rated for 120 CFM or greater
is recommended, such as our Dustless
HEPA Wet+Dry Vacuum.
The releasable tie can be used to fasten
the vacuum hose to the cord of the saw
for added convenience.
WARNING:
This shroud is not intended for use for
bevel cuts. Always use eye and ear
protection when working with power
tools.
Works with:
RIDGID
® •
DEWALT
® •
MAKITA
®
BOSCH
® •
SKIL
® •
MILWAUKEE
®
AND MORE. . .
WARRANTY:
LIMITED WARRANTY
– Your DustBuddie is warrantied
under normal use; provided that use is in accordance with
the Owner’s Manual and the safety rules listed within,
against original defects in material and workmanship for
a period of 30 days. Please note this warranty is limited
to and applies only to the original purchaser. Dustless
Technologies is not responsible and will not be held liable
for statements made by any person(s) as to operation of
this unit that vary from the terms of this limited warranty.
Please read this manual carefully for limitations. There are
no warranties express or implied written or verbal, which
extend beyond the description in this manual.
Simply return the complete unit or part, (transportation
prepaid), to Dustless Technologies, 1285 East 650 South,
Price, Utah 84501. Dustless Technologies assumes no
responsibility for damage or faulty performance caused by
misuse or careless handling, or where repairs have been
made or attempted by others. Proof of purchase date is
required. This warranty gives you specific legal rights and
you may also have other rights, which may vary, from state
to state.
Captures 99%
of Concrete Dust
Dustless Technologies and this product are not affiliated,
connected, or associated with, or sponsored, endorsed, or
approved by any of DEWALT Power Tools and Accessories,
RIDGID, Inc., Shop-Vac Corporation or KCD IP, LLC.
DEWALT
®
is a registered trademark of DEWALT Power
Tools and Accessories
The RIDGID trademark and logo are registered trademarks
of RIDGID, Inc. in the U.S. and other countries.
Makita
®
, LXT
®
, AVT
®
and the Makita
®
logo, Teal color
and Black & White color combination are the registered
trademarks of Makita
®
U.S.A., Inc.
BOSCH
®
is a registered trademark of © Robert Bosch
Tool Corporation
SKIL
®
and SKILSAW Power Tools is a registered trademark
of Chervon Holdings Ltd.
MILWAUKEE
®
is a registered trademark of Milwaukee Tool.
Two-point dust collection
Confirm that the blade is not making contact with the
rubber shield or any other part of the shroud.
Tear along perforation and keep instruction manual
1.
Attach the front rubber dust shield to the
tab in the front of the blade opening.
Replacement parts for this shroud can be ordered
from
Dustless Technologies
with part number
D4001.
GR111_0217_D4000
