background image

 

Hangzhou Roombanker Technology Co., Ltd.

                     

                            A DUSUN company

 

Hangzhou Roombanker Technology Co., Ltd.             Floor 8, building A, Wantong center,  
Tel:86-571-86769027/8  8810480                       Hangzhou 310004, china 
Website: www.dusuniot.com     www.dusunremotes.com   www.dusunlock.com 

Note

5VDC from type C USB; 5~12VDC from intercom connection Port 

5.3

 

TX power consumption during constant emission 

Working 

status 

Rate 

Tx Power/receiver 

Average Value 

Maximum Value 

Unit 

Tx 

250Kbps 

+20dbm 

200 

206 

mA 

Tx 

250Kbps 

+10dbm 

62 

64 

mA 

Tx 

250Kbps 

0dbm 

26 

28 

mA 

Rx 

250Kbps 

Constant receiving 

10 

12 

mA 

Rx 

250Kbps 

Constant receiving 

10 

12 

mA 

RX 

250Kbps 

Constant receiving 

10 

12 

mA 

5.4

 

working current 

Working Mode

 

Working status

Ta=25℃ 

Average value 

Maximum value 

unit 

EZ mode

 

The product is in EZ mode.

 

10 

40 

mA 

Connected and idle

 

The product is connected to the network

 

14.2 

15 

mA 

Deep sleep mode

 

The product in deep sleep mode,

 

50 

uA 

 

6

 

Zigbee RF features 

6.1

 

Zigbee Basic RF features 

Parameter 

Description 

Frequency band 

2.405~2.480GHz 

Wireless standard 

IEEE 802.15.4 

Data transmission rate 

250Kbps 

Antenna type 

PCB antenna with a gain of 1.8dBi, option Ipex 

6.2

 

Zigbee Tx performance 

Performance during constant transmission

 

Parameter 

Min. 

Typ. 

Max. 

unit 

Maximum output power(250Kbps)

 

20 

dBm 

Minimum output power(250Kbps)

 

-30 

dBm 

Output power adjustment step

 

0.5 

dBm 

Output spectrum adjacent-channel rejection ratio 

-31 

dBc 

Frequency error 

-15 

15 

ppm 

6.3

 

Zigbee Rx performance 

Rx sensitivity 

Parameter 

Min. 

Typ. 

Max. 

unit 

PER<8%

RX sensitivity(250Kbps) 

-102 

-101 

-99 

dBm 

 

7

 

BT/BLE performance 

7.1

 

Transmitter

BLE

 

Parameters

 

min

 

Typ

 

max

 

Unit

 

Transmit power

 

dBm 

Summary of Contents for DSW-080



















Reviews: