background image

 

 

13

RMO200                                                                                                                                                         

 

Getting Started 

 
 
 

Seting printer, as well as look of RMO Test Report where given at figures below. 

 

                

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

6.8  Duty Cycles 

 

During tests, RMO200 generates a high DC current that heats up the test set. To 
prevent RMO200 from overheating, certain duty cycles apply depending on the 
used test current.

          

  

 

 

S  i  n  g  l  e       T  e  s  t 

Test current 

(A) 

Cooling time between 

first 4 tests (sec) 

Cooling time after    

4 tests (sec) 

5, 10, 20 

50, 100 

150, 200 

10 

 

C  o  n  t  i  n  u  o  u  s       T  e  s  t 

Test current 

(A) 

Maximal test

 

duration 

 

 

time (sec)  

Cooling time 

between tests (sec) 

5,10,20 
50, 100 

300 0 

150, 200 

150 

300 

                                  
 

A built-in control prevents these cooling times from being skipped. If you try to  
start a test within the cooling period, the display shows "Wait" and a timer   
counting down. After the cooling period has elapsed, start the test using the set  
test parameters by pressing the 

  button. Cooling of RMO200 is supported by       

a built-in fan that is automatically activated every time a test is started from the 

Test 

menu. It continues running 5 minutes after the test is finished. 

 
 
 
 
 
 

Table 6-11: 
Cooling time 
between 
single 
tests 

Table 6-12: 
Cooling time 
between 
continuous 
tests 

Summary of Contents for RMO200































Reviews: