background image

  

 
 

17 

trademark which it includes or describes, and is expressly prohibited from modifying the information or 
creating  derivative  works  without  the  express  written  consent  of  DVC  Company.  DVC  models 
represented  in  photographs  may  differ  slightly  from  products  shipped  due  to  continuing  product 
improvements  and  variations.  DVC  reserves  the  right  to  make  changes  to  product  specifications  and 
documentation  at  any  time  without  notice.  The  information  in,  or  references  from,  this  document  are 
believed  to  be  accurate  and  reliable,  however,  no  responsibility  is  assumed  by  DVC  for  its  use.  DVC 
reserves the right to change, modify or correct the information contained in this document at any time 
without  notice.  While  DVC  has  used  all  reasonable  efforts  to  indicate  and  to  supply  information 
regarding  trademarks  used  in  this  publication,  the  absence  of  a  trademark  identifier  is  not  a 
representation that a particular mark is not a trademark. All non-DVC products, brand names, company 
names are trademarks or registered trademarks of their respective owners, and appear in this document 
for reference only.  

 
Disclaimer: 

The  information  in  this  document  is  provided  "as  is."  DVC  expressly  disclaims  all 

representations and warranties of any kind regarding the contents or use of the information including, but 
not limited to, express and implied warranties of accuracy, completeness, merchantability, fitness for a 
particular  use,  or  non-infringement.  In  no  event  will  DVC  be  liable  for  any  direct,  indirect,  special, 
incidental or consequential damages, including lost profits, lost business, or lost data, resulting from the 
use  or  reliance  upon  the  information,  whether  or  not DVC  has  been  advised  of  the  possibility  of  such 
damages. 

Summary of Contents for DVC-340


























Reviews: