S
S
e
e
r
r
v
v
i
i
c
c
e
e
M
M
a
a
n
n
u
u
a
a
l
l
5.3
When pause mode lasts for 10 minutes without any key is activated, it enters idle mode automatically.
5.4
The resistance and ramp incline levels returns to 1. When “Start” is pressed again, the position of the gear motor resumes and the ramp incline
return to the level just before pause.
END MODE
6.1 At the end of the program, message window will display “CONGRATULATIONS YOU HAVE COMPLETED YOUR WORKOUT PRESS THE
STOP KEY TO END OR A USER KEY TO SAVE” showing the workout data for 1minutes.
6.2
END MODE workout information
：
6.2.1
In message window,
『
AVG SPD XX.X
』
、
『
AVG WATT XXX
』
、
『
AVG HR XXX
』
、
『
LAPS XX
』
、
『
ALT XXXX FT
』
each lasts for 3 seconds.
6.2.2
The message window is followed by displaying “CONGRATULATIONS YOU HAVE COMPLETED YOUR WORKOUT PRESS THE STOP
KEY TO END OR A USER KEY TO SAVE” with prompt of pressing start key to restart the program or pressing “Stop” key once to exit or
pressing “User” key and follow the MW instructions to save the program which has been finished by the custom user.
6.2.3
CAL will show the total calorie value of the workout, time window the total workout time and DIST window the total distance of the workout.
6.3
When TIME ends the count down to the end with end mode displayed for 1 minute without any key activation, it returns to idle mode automatically.
RESET MODE
7.1
Under idle mode (except console has been locked that must be unlocked prior to having the reset function), press “Stop” key for 3 seconds to
enter reset function and restart the system.
Summary of Contents for XE515SD-YE005
