57083 Vacuum Adapter
57065 Cone Muffler
57066 Muffler Body
95526 O-Ring
96197 Dowel Pin
57068 Vac Nozzle
57067 Vac Tube
Machine Exhaust Assemblies
Self Generated Vacuum (Vac-Ready) / Machine Exhaust
For Models: 57801, 57802, 57803
2
(PD97•14)
All Models
7-1/4" (184)
4-1/4" (108)
2.75 lbs. (1.2 kg)
13 (368)
83 dBA
.18 (134)
8,000
90 (6.2)
Model
Length
Height
Machine
Air Flow Rate
Sound
Motor
Motor
Air Pressure
Number
Inch (mm)
Inch (mm)
Weight
SCFM (LPM)
Level
HP (W)
RPM
PSI (Bars)
Additional specifications: Air Inlet Thread 1/4" (6 mm) NPT • Hose Size 1/4" (6 mm)
Important Operating, Maintenance and Safety Instructions
Carefully read all instructions before operating or servicing any Dynabrade® Abrasive Power Tool.
Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Important: All Dynabrade air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.
Operating Instructions:
Warning:
Eye, face and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death. Follow safety
procedures posted in workplace.
1. With power source disconnected from tool, securely fasten abrasive/accessory on tool.
2. Install air fitting into inlet bushing of tool. Important: Secure inlet bushing of tool with a wrench before attempting to install the air fitting to avoid damaging
valve body housing.
3. Connect power source to tool. Be careful not to depress throttle lever in the process.
4. Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should be
serviced to correct the cause before use.
Maintenance Instructions:
1. Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be serviced to correct
the cause before use.
2. Some silencers on air tools may clog with use. Clean and replace as required.
3. All Dynabrade air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example : if the tool
specification state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute). Dynabrade Air Lube (P/N 95842: 1pt. 473ml.) is recommended.
4. An air line filter-regulator-lubricator must be used with this air tool to maintain all warranties. Dynabrade recommends the following: 11289 Air Line Filter-
Regulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of pneumatic
components. Operates 40 CFM @ 100 PSI has 3/8" NPT female ports.
5. Use only genuine Dynabrade replacement parts. To reorder replacement parts, specify the Model #, Serial #, and RPM of your machine.
6. A motor tine-up kit (P/N 96024) is available which includes assorted parts to help maintain motor in peek operating condition.
7. Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters, keytones,
chlorinated hydrocarbons or nitro carbons.
Safety Instructions:
Products offered by Dynabrade should not be converted or otherwise altered from original design without expressed written consent from
Dynabrade, Inc.
•
Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI).
•
Operate machine for one minute before application to workpiece to determine if machine is working properly and safely before work begins.
•
Always disconnect power supply before changing abrasive/accessory or making machine adjustments.
•
Inspect abrasives/accessories for damage or defects prior to installation on tools.
•
Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.
57093 Vacuum Adapter
57065 Cone Muffler
57066 Muffler Body
56027 Muffler Insert (3)**
56028 Muffler Cap
57065 Cone Muffler
57066 Muffler Body
56027 Muffler Insert (3)**
56028 Muffler Cap
Central Vacuum / Machine Exhaust
For Model: 57804
Non-Vacuum / Machine Exhaust
For Model: 57800
Shaded parts Represent 57112 Muffler Assembly.
** Muffler inserts available in Package of 30 - P/N 56054.
