2
One Year Warranty
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the
date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall
repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our
examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations,
instructions and safety practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to
affect its normal performance. Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.
Important Operating, Maintenance and Safety Instructions
Carefully read all instructions before operating or servicing any Dynabrade
®
Abrasive Power Tool.
Warning:
Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.
Operating Instructions:
Warning:
Eye, face, sound, respiratory, and body protection must be worn while operating power tools. Failure to do so may result in serious
injury or death. Follow safety procedures posted in workplace.
1.
With power source disconnected from tool, securely fasten abrasive/accessory on tool.
2.
Install air fitting into inlet bushing of tool.
Important:
Secure inlet bushing of tool with a wrench before attempting to install the air fitting
to avoid damaging valve body housing.
3.
Connect power source to tool. Be careful not to depress throttle lever in the process.
Maintenance Instructions:
1.
Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be
serviced to correct the cause before use.
2.
Some silencers on air tools may clog with use. Clean and replace as required.
3.
Use only genuine Dynabrade replacement parts. To reorder replacement parts, specify the
Model #
,
Serial #
, and
RPM
of your machine.
4.
A Motor Tune-Up Kit (P/N
96169
) is available which includes assorted parts to help maintain motor in peek operating condition.
Please refer to Dynabrade’s Preventative Maintenance Schedule for a guide to expectant life of component parts.
5.
Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids,
esters, keytones, chlorinated hydrocarbons or nitro carbons.
•
Important:
User of tool is responsible for following accepted safety codes such as those published by the American National
Standards Institute (ANSI).
•
Always disconnect power supply before changing abrasive/accessory or making machine adjustments.
•
Inspect abrasives/accessories for damage or defects prior to installation on tools.
•
Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No.
95903
) for more complete safety information.
Notice
All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic
motors can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply
into motor bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our
warranty obligation is contingent upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean
air, wet air or a lack of lubrication during the use of this tool.
(APD01•12)
Safety Instructions:
Products offered by Dynabrade should not be converted or otherwise altered
from original design without expressed written consent from Dynabrade, Inc.
Model
Pad
Motor
Sound
Air Flow Rate
Air Pressure
Orbit Diameter
Weight
Length
Height
Number
Size
RPM
Level
CFM/SCFM PSIG
(Bars)
Inch Pound
Inch
Inch
All Models
Various
20,000
83 dB(A)
1/9
90 (6.2)
3/16
1
5
3
Additional Specifications: Air Inlet Thread 1/4" NPT
