Apply to set screw (included)
Loctite: A
2
= Loctite #271
A
8
= Loctite #567
KEY
A
Index Key
No. Part # Description
1 57751 Button (w/set screw)
2 57778 Bracket
3 57728 Nozzle
4 57727 Valve Cartridge
5 95523 O-Ring
6 56076 Throttle Valve Plug
7 95074 Hose Fitting
8 97327 Screw (2)
9 95955 10' Tubing
10 10293 Shrink Tube
11 95952 Quick Disconnect
96236 Motor Tune-Up Kit
•
Includes assorted parts to help
maintain and repair motor.
Optional Accessories
57777 Wet Assembly
52296 Repair Collar
•
Specially designed collar for use in vise to
prevent damage to valve body housing
during disassembly/assembly.
96210 Bearing Removal Tool
•
This tool is used to pass through the I.D.
of the bearing plate and to push against
the I.D. of the bearing.
96216, 96243, 96244 Bearing Press Tool
•
This tool is used to safely press a
bearing plate or onto a shaft.
Dynabrade Air Lube
•
Formulated for pneumatic equipment.
•
Absorbs up to 10% of its weight in water.
•
prevents rust and formation of sludge.
•
Keeps pneumatic tools operating longer
with greater power and less down time.
95842: 1pt. (473 ml)
95843: 1 gal. (3.8 L)
50971 Lock Ring Tool
•
Lock Ring Tool has a 3/8 in.
square socket for use with 3/8 in.
drive; breaker bar, ratchet head,
or torque wrenches.
DYNABRADE
®
DYNABRADE, INC.,
8989 Sheridan Drive
•
Clarence, NY 14031-1490
•
Phone: (716) 631-0100
•
Fax: 716-631-2073
•
International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l.,
Zone Artisanale
•
L-5485 Wormeldange—Haut, Luxembourg
•
Telephone: 352 76 84 94 1
•
Fax: 352 76 84 95 1
© DYNABRADE, INC., 2003
PRINTED IN USA
Visit Our Web Site: www.dynabrade.com
Email: Customer.Service@Dynabrade.com
7
10
11
9
1
5
2
3
4
A
2
A
8
A
2
A
8
A
8
Disassembly/Assembly Instructions - Dynafine
®
(Continued)
4. Orient the throttle lever to the operators desired grip and positioning. Note: Allow for additional rotation of the 01546 Housing as the 01461 Lock Nut is tightened.
5. With a firm hold on the 01546 Housing to reduce its rotation, use a 34 mm or an adjustable wrench to tighten the 01461 Lock Nut. (Torque to 45 N•m/400 in.- lbs.)
Important: When performing this procedure be careful not to entirely separate the 01546 Housing from the valve body assembly. Loosen the 01461 Lock Nut only enough to
make the adjustment.
Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the tool, the tool
should be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet with throttle lever depressed.
Operate tool for 30 seconds to determine if tool is operating properly and to allow lubricating oils to properly permeate motor.
Loctite
®
is a registered trademark of loctite Corp.
96232 #2 Arbor Press
•
This arbor press is ideal for
the disassembly and assembly
of air motors.
96346 Bearing Separator
•
Use the separator to remove
bearings and gears.
95542 Grease 10 oz.
•
Multi-purpose grease for all types of
bearings, cams, gears.
•
High film strength; excellent
resistance to water, steam, etc.
•
Workable range 0˚ F to 300˚ F.
95541 Push-type Grease Gun
•
One-hand operation.
6
8
