background image

3

RIDER USE AND REQUIRED PARENTAL SUPERVISION

RIDERS MUST NOT EXCEED THE WEIGHT LIMIT OF 130 LB (59 KG) AND 
MUST BE OVER 3 YEARS OLD. NEVER ALLOW MORE THAN 2 CHILDREN TO 
RIDE THE RIDE-ON TOY SIMULTANEOUSLY.

The age grade for the electric ride-on toy is for 3 years and older. Just because 
your child is within the age and weight limitations specified for the electric ride-
on toy, does not mean that his/her size is appropriate to fit or maintain control of 
the electric ride-on toy, or that he/she is capable of safely operating the electric 
ride-on toy. You are the best judge of whether you or your child can safely operate 
the electric ride-on toy; this includes determining whether your child is at the 
appropriate developmental stage for safe use of the electric ride-on toy. Any rider 
that is unable to fit comfortably on the electric ride-on toy should never attempt to 
ride it. A parent's decision to allow their child to use the electric ride-on toy should 
be based on the child's maturity, skill and their ability to follow rules. Remember 
that the electric ride-on toy is intended for use only by children who are, at a 
minimum, able to comfortably and safely operate it.
Children operating the electric ride-on toy should be supervised by an adult at all 
times. Parents should ensure that children only use the electric ride-on toy safely 
and within their age and physical limits.
This manual contains very important safety information. It is your responsibility to 
completely review this information and make sure that all riders understand all of 
the warnings, cautions, instructions and safety topics addressed in this manual 
and to assure that all riders are able to safely and responsibly use the electric 
ride-on toy. You should periodically review and reinforce all information in this 
manual with all riders, especially children. You should also regularly inspect and 
maintain your electric ride-on toy to ensure the safety of all riders. Make sure that 
your new electric ride-on toy is properly fitted to any child riding it; that it is in good 
repair and safe operating condition; that you and your child have gone over the 
use, operation and safety information in this manual; that you and your child have 
learned and understand what to do and what not to do with your new electric ride-
on toy, including observing all applicable laws, rules and common sense.
Children should be made aware of all possible riding hazards and correct riding 
behavior before they ride the electric ride-on toy and should be supervised by an 
adult at all times. Please explain the following to them as often as necessary.

Summary of Contents for 24V TRAIL RACER

































Reviews: