background image

21

22

MP3

Audio Input Jack

Use the Audio input cable (Included) to connect your MP3 player or other 
compatible audio device with this vehicle to listen to and enjoy music.

1. Plug one end of the audio input cable (Included) into the audio input jack on the 
vehicle as shown.

2. Plug the other end of the audio input cable into the headphone jack on your 
audio device or MP3 player.

3. Adjust your audio device or MP3 player volume to low level and turn the power 
switch on your vehicle to the “ON” position.

4. Then adjust the volume to increase or decrease its sound level as desired.

NOTE:

 MP3 player or Audio Device not included.

 WARNING:

 Do not let use of an MP3 player or other audio device interfere with 

safe riding.

 DUMP BED WARNING:

•  Maximum load weight on the dump is 5kg (11lb).

•  No stepping on or in dump bed.

•  No climbing on or in dump bed.

•  Never ride in dump bed.

NOTE:

 For your safety, this ride-on toy has been designed with a one second delay start. 

When the pedal is pressed, the ride-on toy will start to move one second later.

IMPORTANT

•  Always stop vehicle when changing the direction to avoid damage to the gears 

and motor.

•  This vehicle has an adjustable seat belt; instruct children on how to fasten the 

seat belt before using.

•  Do not let any child touch the wheels or be near them when the car is moving. 
•  To avoid accidents, inspect the vehicle before riding to ensure that it is in proper 

working order and safe to ride.

•  This toy has no brake; to stop, remove foot from the foot pedal.
•  Check all the screws, cap nuts and protective coverings regularly and tighten as 

required. Check plastic parts on a regular basis for cracks or broken pieces. 

•  Your new battery must be charged for at least 18 hours before you use it in your 

vehicle for the first time.

•  Do not wash the vehicle with water; clean it with a cloth.

SAFETY PRECAUTIONS

•  The child must have adult supervision at all times.
•  Do not ride on the road, footpaths, near pools, or bodies of water.
•  Do not allow children under the recommended age to ride the vehicle; refer to 

the age grading.

•  Do not allow riders over the recommended weight rating or under the age 

grading to use the vehicle.

•  To stop the vehicle, you must take your foot off the pedal.
•  Charging should only be done by an adult.
•  An adult must teach the child how to operate the vehicle.
•  Do not ride on hills or slopes, in sand or on other soft, wet, or slippery surfaces.
•  Do not use a different size battery. Use only original or recommended 

replacement batteries.

•  The vehicle is designed to carry only a maximum weight of 130 lbs at a time. 

Never allow more than two riders or over-load the vehicle.

•  This product should be assembled and checked by adults before use.

 WARNING:

  This ride-on has no brake; to stop take foot off foot pedal. Do not park 

or ride on any slopes or steep inclines.

Audio Input Jack

MP3 here

Audio Input Cable 
(Included)

Summary of Contents for 24V UTV



















Reviews: