background image

                 

Embedded  Solutions

                    Page  2

 

   

 

cPCIBPMC6U

 

cPCI and PMC Compatible Carrier

 

Dynamic Engineering 
150 DuBois St Suite B/C 
Santa Cruz, CA 95060 
831-457-8891  

This document contains information of 
proprietary interest to Dynamic Engineering. It 
has been supplied in confidence and the 
recipient, by accepting this material, agrees that 
the subject matter will not be copied or 
reproduced, in whole or in part, nor its contents 
revealed in any manner or to any person except 
to meet the purpose for which it was delivered. 
 
Dynamic Engineering has made every effort to 
ensure that this manual is accurate and 
complete. Still, the company reserves the right to 
make improvements or changes in the product 
described in this document at any time and 
without notice. Furthermore, Dynamic 
Engineering assumes no liability arising out of 
the application or use of the device described 
herein. 
 
The electronic equipment described herein 
generates, uses, and can radiate radio 
frequency energy. Operation of this equipment 
in a residential area is likely to cause radio 
interference, in which case the user, at his own 
expense, will be required to take whatever 
measures may be required to correct the 
interference. 
 
Dynamic Engineering’s products are not 
authorized for use as critical components in life 
support devices or systems without the express 
written approval of the president of Dynamic 
Engineering. 
 
Connection of incompatible hardware is likely to 
cause serious damage.

 

© by Dynamic Engineering. 
Other  trademarks  and  registered trademarks are owned by their 
respective  manufactures.

 

Summary of Contents for cPCIBPMC6U
















Reviews: