background image

10

Copyright © 2014 - 2022 Dynamic Projection Institute GmbH. All rights reserved. http://www.dynamicprojection.com

Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice. 

DMX fixture definition for v10021

Caution! 

Since 2022 all the Mirror Head units are leaving the factory with an entirely 

NEW GENERATION 

OF FIRMWARE 10021

. To download the manual for the new firmware 10018 and newer, please visit our Mirror 

Head support page.  

https://www.dynamicprojection.com/mh-support/

Channel

Function 

Value

Notes

#10 

 

LED Main Intensity 

 

0-255 

 

#14 

 Acceleration 

default 

 0

#12 

 

LED Green Intensity 

 

0-255

 

 

Damping amount  

 

1-255 

 

Value is the DAMPING amount in 

        TRACKING 

Mode

#11 

 

LED Red Intensity 

 

0-255 

 

 

 

Acceleration  

 

 

1-255 

 

Value is the ACCELERATION amount in 

        VECTOR 

Mode

#13 

 

LED Blue Intensity 

 

0-255

 

 

In FX Mode TILT Frequency 

0-255 

 

In FX Mode TILT Frequency

#9 

 

Projector power OFF 

 

250-255

  Projector 

power 

ON 

 230-238

  Mirror 

Head 

STANDBY 

 50-58 

 

  Mirror 

Head 

ON 

  28-38

QIG - Version 2.8

Mirror Head Quick Installation Guide

For the full manual please visit 

https://www.dynamicprojection.com/mh-support/

Summary of Contents for MH08











Reviews: