background image

 

 

- 3 - 

Jump height

50

60mm 

Forward speed

:

 8m/min 

Metal sheet

280mm×350mm 

Power

:

 ER12 

Overall dimensions

:

 760mm×410mm×970mm 

Engine oil

Grade of Engine oil SF or SG; SAF10W

30 

Engine oil

0.30L 

Fuel

Unleaded gasoline with a pump octane rating of 90 or higher 

Fuel capacity

3L 

Spark plug

NGK: CR5HSB; DENSO: U16FSR

UB 

 

SAFETY 

1.

 

Before  starting  operation,  the  operator has  to  check  that  all  control 

and safety devices function properly. 

2.

 

To  prevent  fire  hazards  and  to  provide  adequate  ventilation  for 

stationary  equipment  applications keep the engine at  least  3 feet (1 

meter)  away  from  building  walls  and  other  equipment  during 

operation.   

3.

 

Don't  allow  children  to  operate  the  engine.  Keep  children  and  pets 

away from the area of operation. 

4.

 

Know how to stop the engine quickly, and understand the operation 

of  all  controls.  Never  permit  anyone  to  operate  the  engine  without 

prior instructions. 

5.

 

Do not place flammable objects close to the engine. 

6.

 

The  max  gradient  of  20°  must  not  be  exceeded  when  the  engine 

working. 

7.

 

Wear  safety  shoes,  and  eye  protection  glasses  in  case  of  trench 

operation where falling sand stones maybe ejected.   

8.

 

When the machine working, prohibit the operator from the machine. 

Summary of Contents for TRE-75 TAMPING RAMMER

































Reviews:

Related manuals for TRE-75 TAMPING RAMMER