background image

D016

-

047

-

1                     LeakVIEW User Guide                 Page 22 of 22

 

7.1 WARRANTY PERIOD

 

The LeakVIEW system has been carefully tested and inspected before shipment and is guaranteed to be 

free from defective materials and workmanship for a period of twelve months from date of purchase 

(invoice date).  

 

 

7.1.2 CONDITIONS OF WARRANTY

 

1.

 

This warranty is in addition to and does not affect any statutory rights of consumer purchasers. This 
warranty is valid worldwide on a "Return to supplier basis

”.

 

2.

 

This warranty covers breakdowns due to design or manufacturing faults; it does not apply to damage, 
however caused, wear and tear, neglect, unauthorised adjustment or repair, or any items of limited 
natural life such as the lid seal. Failure due to filling with water of incorrect temperature is also

 

excluded.

 

3.

 

In the event of a failure, please take the following action:

 

 

a] Refer to the Troubleshooting guide in Section 6 of this User guide and if possible correct the 

 

fault.

 

 

b] If the fault cannot be resolved, please contact the supplier at the address given on the cover of the 

 

in the CONTACT INFORMATION section of this guide.

 

 

4.

 

The warranty period applicable shall be 12 months from the date of delivery provided that:

 

 

 

a] Notice in writing of the defects complained of shall be given to the supplier (The Seller) upon their 

 

appearance, and:

 

 

 

b] Such defects shall have arisen from the Seller's faulty design, workmanship or materials.

 

 

 

c] The defective goods shall be returned to the Seller's premises at the Purchaser's expense if so 

 

requested by the Seller.

 

 

 

d] Any repaired or replaced goods shall be redelivered by the Seller free of charge to the original 

 

point of delivery but otherwise in accordance with and subject to the supplier

s Conditions of Sale.

 

 

 

e] Alternatively the Seller shall be entitled at its absolute discretion to refund the price of the defective 

 

goods in the event that such price shall already have been paid by the Purchaser to the Seller, or, if 

 

such price has not been so paid, to relieve the Purchaser of all obligation to pay the same by the

 

 

issue of a credit note in favour of the Purchaser in the amount of such price.

 

 

WARRANTY

 

This section describes:

 

• 

Routine maintenace

 

• 

User serviceable parts

 

• 

Emergency maintenance

 

• 

Cleaning 

 

SECTION 7: WARRANTY

 

Summary of Contents for LeakVIE M016























Reviews: