• E
Q U
I P P
E D W I
T H G E C K O ' S E X C L
U S I V
E •
Smart
Winter
Mode
TM
9919-100614
Summary of control panel parameters
FDxx
Filter cycle duration
FSxx
Filter cycle start delay
LocX
Control pad lockout
EDxx
Economy mode duration
ESxx
Economy mode delay
P xx
Purge cycles
Digital control pad lockout
This function allows you to prevent unauthorized parameter setting
of the unit. This feature is especially helpful when young children
have access to the keypad.
There are two modes you can choose from:
Full
lock or
Partial
lock.
Full
lock means that all keypad functions are locked.
Partial
lock
means that the basic functions of the spa will remain accessible
(pumps, blower and light), but it will be impossible to change the
temperature Set Point, to override the Economy mode or to
enter the Programming mode.
When control pad is locked, the "Lock" icon will be displayed.
Locking your digital control pad:
1- Press and hold
Econo
key for 5 seconds.
2- The display will show
LocP
, with "P"
representing
Partial
lock.
3- Release key and keypad will be in
Partial lock
mode. Keep key pressed down for 5 more
seconds if you want to be in
Full
lock mode.
The "LocF" message will then be displayed.
When control pad is locked, all automatic functions of the system run
as usual. If a key is pressed down, a "LocP" or "LocF" message will be
displayed for 1 second. To unlock the keypad, simply press and hold
Econo
key again for 5 seconds.
LocP
LocF
Inverted display
Press and hold
Light
key for 5 seconds to invert the display.
If a power-up occurs, the display always returns to default mode.
ED12
ES20
Economy mode
To save energy, the Economy mode Set Point is 11˚C (20˚F)
below the Normal mode Set Point.
The "Economy Mode" icon lights up when Economy
mode is on.
Setting Economy mode:
1- Press
Econo
key.
2- The display will show
EDxx
, with "xx"
representing the Economy mode duration.
3- Use
Up
or
Down
key to change setting.
4- Press
Econo
key again.
5- The display will show
ESxx
, with "xx" representing
the delay before mode starts.
6- Use
Up
and
Down
arrows to change setting.
7- Press
Econo
key a third time to store settings.
40-minute Economy mode time-out:
If you turn a pump, blower or
light on while Economy mode is on, the Economy mode will be
interrupted and will only resume 40 minutes after the system has
turned the last active output off. The "Econ" message or "Economy
Mode" icon will flash, depending on your system configuration.
K-4 keypad is mandatory when some options are selected.
*
"CLE" message
Every two weeks, the "CLE" message might be displayed indicating
to clean the filter (depending on your spa configuration). Press any
key to reset the message.
Filter cycles
The system automatically performs 2 filter cycles per day, at 12-
hour intervals. During a filter cycle, Pumps 2 & 3 and blower run
for one minute. Pump 1 then runs at low speed for the remaining
of the cycle and "Filter Cycle" icon lights up. (If system is equipped
with a circulation pump, all pumps and blower run for one minute.
Circulation pump then runs for the remaining of the cycle and
"Filter Cycle" icon lights up.)
Setting filter cycles:
1- Press
Filter
key.
2- The display will show
FDxx
,
with "xx"
representing the duration in hours.
3- Use
Up
and
Down
arrows to change setting.
4- Press
Filter
key again.
5- The display will show
FSxx
,
with "xx"
representing the delay before cycle starts.
6- Use
Up
and
Down
arrows to change setting.
7- Press
Filter
key to store settings.
40-minute filter cycle time-out:
If you turn a pump, blower or
light on during a filter cycle, the cycle will be interrupted and will
only resume 40 minutes after the system has turned the last active
output off.
FD10
FS06
Purge cycles
The system can perform a number of purge cycles per day.
During a purge cycle, pumps and blower run for two minutes
and "Filter Cycle" icon lights up.
Setting purge cycles:
1- Press
Filter
key.
2- The display will show
P xx
,
with "xx"
representing the currently set number of
daily purge cycles.
3- Use
Up
and
Down
arrows to change setting.
4- Press
Filter
key to store settings.
P 24
Boost filtration mode
This function allows you to speed up filtration after intensive use of
your spa or to mix chemicals. Simply keep
Pump 1
key pressed
down for 5 seconds. Pump 1 will run at high speed for 45 minutes
and "BOO" message will be displayed. Ozonator is also activated.
Real-time clock *
Use
Clock
key to set real-time clock. The display toggles every
5 seconds alternately showing the hourly time and the current
water temperature.
Water level sensor
If the system is equipped with an optional water level sensor and the
sensor detects an insufficient level of water in the tub, the system will
prevent pumps from starting and will display the "H20" message.
Pumps will be allowed to turn back on when water level returns
above sensor.
