background image

23

DX-MLET21

www.dynexproducts.com

90-DAY LIMITED WARRANTY 

Definitions: 

The Distributor* of Dynex branded products warrants to you, the original purchaser of this new Dynex-branded product (“Product”), that the Product 
shall be free of defects in the original manufacturer of the material or workmanship for a period of ninety (90) days from the date of your purchase of 
the Product (“Warranty Period”). 
For this warranty to apply, your Product must be purchased in the United States or Canada from a Best Buy branded retail store or online at 

www.bestbuy.com 

or 

www.bestbuy.ca 

and is packaged with this warranty statement. 

How long does the coverage last? 

The Warranty Period lasts for ninety (90) days from the date you purchased the Product. Your purchase date is printed on the receipt you received with 
the Product. 

What does this warranty cover? 

During the Warranty Period, if the original manufacture of the material or workmanship of the Product is determined to be defective by an authorized 
Dynex repair center or store personnel, Dynex will (at its sole option): (1) repair the Product with new or rebuilt parts; or (2) replace the Product at no 
charge with new or rebuilt comparable products or parts. Products and parts replaced under this warranty become the property of Dynex and are not 
returned to you. If service of Products or parts are required after the Warranty Period expires, you must pay all labor and parts charges. This warranty 
lasts as long as you own your Dynex Product during the Warranty Period. Warranty coverage terminates if you sell or otherwise transfer the Product. 

How to obtain warranty service? 

If you purchased the Product at a Best Buy retail store location or from a Best Buy online website (

www.bestbuy.com 

or 

www.bestbuy.ca

), please take 

your original receipt and the Product to any Best Buy store. Make sure that you place the Product in its original packaging or packaging that provides 
the same amount of protection as the original packaging. 
To obtain warranty service, in the United States and Canada call 1-800-305-2204. Call agents may diagnose and correct the issue over the phone. 

Where is the warranty valid? 

This warranty is valid only in the United States and Canada at Best Buy branded retail stores or websites to the original purchaser of the product in the 
country where the original purchase was made. 

What does the warranty not cover? 

This warranty does not cover: 

Customer instruction/education 

Installation 

Set up adjustments 

Cosmetic damage 

Damage due to weather, lightning, and other acts of God, such as power surges 

Accidental damage 

Misuse 

Abuse 

Negligence 

Commercial purposes/use, including but not limited to use in a place of business or in communal areas of a multiple dwelling condominium or 
apartment complex, or otherwise used in a place of other than a private home. 

Modification of any part of the Product, including the antenna 

Display panel damaged by static (non-moving) images applied for lengthy periods (burn-in). 

Damage due to incorrect operation or maintenance 

Connection to an incorrect voltage or power supply 

Attempted repair by any person not authorized by Dynex to service the Product 

Products sold “as is” or “with all faults” 

Consumables, including but not limited to batteries (i.e. AA, AAA, C etc.) 

Products where the factory applied serial number has been altered or removed 

Loss or Theft of this product or any part of the product 

Display panels containing up to three (3) pixel failures (dots that are dark or incorrectly illuminated) grouped in an area smaller than one tenth 
(1/10) of the display size or up to five (5) pixel failures throughout the display. (Pixel based displays may contain a limited number of pixels that 
may not function normally.) 

Failures or Damage caused by any contact including but not limited to liquids, gels or pastes. 

REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR EXCLUSIVE REMEDY FOR BREACH OF WARRANTY. DYNEX SHALL NOT BE LIABLE 
FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, INCLUDING, 
BUT NOT LIMITED TO, LOST DATA, LOSS OF USE OF YOUR PRODUCT, LOST BUSINESS OR LOST PROFITS. DYNEX PRODUCTS MAKES NO OTHER EXPRESS 
WARRANTIES WITH RESPECT TO THE PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY 
IMPLIED WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE 
WARRANTY PERIOD SET FORTH ABOVE AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THE WARRANTY PERIOD. SOME 
STATES, PROVINCES AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION 
MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE 
TO STATE OR PROVINCE TO PROVINCE. 
Contact Dynex: 

1-800-305-2204 

www.dynexproducts.com

 

DYNEX is a trademark of Best Buy and its affiliated companies 
*Distributed by Best Buy Purchasing, LLC 
7601 Penn Ave South, Richfield, MN 55423 U.S.A. 
©2020 Best Buy. All rights reserved 

Summary of Contents for 600603265891

























Reviews: