Dynex DX-LTDVD19-09, User Manual

12

Using the TV

Connecting a camcorder or video game

To connect a camcorder or video game:

1

Follow the instructions in “Connecting a VCR with a standard AV 
cable” on page 10.

Connecting a computer

To connect a computer:

1

Make sure that the computer has a VGA jack. See the 
documentation that came with the computer.

2

Make sure that the computer and your TV/DVD combo are turned 
off.

3

Connect a VGA cable (not supplied) to the 

VGA IN

 jack on the 

back of your TV/DVD combo, then connect the other end of the 
cable to the 

VGA

 jack on the computer.

4

Connect an audio cable (not included) to the 

PC AUDIO IN

 jack 

on the back of your TV/DVD combo, then connect the other end of 
the cable to the 

AUDIO OUT

 jacks on the computer.

5

Turn on your TV/DVD combo first, then turn on the computer.

6

Press 

INPUT

, press 

CH+

 or 

CH–

 to select 

PC

, then press 

ENTER

.

7

If you see video “noise” on the screen, you may need to adjust the 
brightness or contrast on your TV/DVD combo or the computer’s 
video resolution or refresh rate on the computer. For information 
about adjusting the video on your TV/DVD combo, see “Adjusting 
the computer image” on page 14. For information about 
adjusting the video on the computer, see the documentation that 
came with the computer.

Supported video modes for a computer

Note:

 If the computer does not support one of the following video modes, 

you may need to replace or add a video card.

Your TV/DVD combo supports the following video modes:

Using the TV

All instructions use the remote control unless otherwise noted.

Turning on your TV/DVD combo

To turn on your TV/DVD combo:

1

Plug the power cord into a power outlet. Your TV/DVD combo 
enters standby mode and the power indicator lights red.

2

Press 

POWER

. Your TV/DVD combo turns on and the power 

indicator lights green.

3

To put your TV/DVD combo into standby mode, press 

POWER 

again.

Caution:

 When your TV/DVD combo is in standby mode, power is still 

flowing into your TV/DVD combo. To disconnect all power, unplug the 
power cord.

Selecting the TV signal source

To select the TV signal source:

1

Press 

MENU

, then press 

CH+

 or 

CH–

 repeatedly until the 

Channel

 menu appears.

2

Press 

VOL+

 or 

ENTER

 to open the 

Channel

 menu.

3

Press 

CH+

 or 

CH–

 repeatedly to select 

Tuner

, then press 

VOL+

or 

VOL–

 to select 

Antenna

 or 

Cable

.

Setting up the channel list

The first time you use your TV/DVD combo or if you move your 
TV/DVD combo to a different broadcast area, you need to scan for 
channels. Your TV/DVD combo scans for channels available in your area 
and stores the channel information in the channel list. When you press 

CH+

 or 

CH–

, your TV/DVD combo goes to the next or previous channel 

in the channel list and skips any channel numbers that do not have a 
broadcast signal.

To set up the channel list:

1

Press 

MENU

, then press 

CH+

 or 

CH–

 repeatedly until the 

Channel

 menu appears.

2

Press 

VOL+

 or 

ENTER

 to open the 

Channel

 menu.

Mode Resolution

Line frequency (KHz) Frame frequency (Hz)

VGA

640 × 480

31.5

60

SVGA 800 × 600

37.9

60

XGA

1024 × 768

48.4

60

PC

A

UDIO

IN

V

GA

IN

Channel

Video

Audio

Channel

Lock

Function

Select

Back

EXIT

CH+/-
VOL+/-

Tuner                             Antenna
Channel Scan
Channel Skip
Channel Label

Channel

Video

Audio

Channel

Lock

Function

Select

Back

EXIT

CH+/-
VOL+/-

Tuner                             Antenna
Channel Scan
Channel Skip
Channel Label