background image

Important safety instructions

5

Warning:

 To prevent fire or shock hazard, do not expose this appliance to 

rain or moisture.

Caution:

 To prevent electric shock do not use this polarized plug with an 

extension cord, receptacle or other outlet unless the blades can be fully 
inserted to prevent blade exposure.

Caution:

 These servicing instructions are for use by qualified service 

personnel only. To reduce the risk of electric shock, do not perform any 
servicing other than that contained in the operating instructions 
unless you are qualified to do so.

Caution:

 Use of any controls, adjustments, or procedures other than those 

specified herein may result in hazardous radiation exposure.

Important safety instructions

1

Read these instructions.

2

Keep these instructions.

3

Heed all warnings.

4

Follow all instructions.

5

Do not use this apparatus near water.

6

Clean only with dry cloth.

7

Do not block any ventilation openings. Install in accordance with 
the manufacturer’s instructions.

8

Do not install near any heat sources such as radiators, heat 
registers, stoves, or other apparatus (including amplifiers) that 
produce heat.

9

Do not defeat the safety purpose of the polarized or 
grounding-type plug. A polarized plug has two blades with one 
wider than the other. A grounding type plug has two blades and 
a third grounding prong. The wide blade or the third prong are 
provided for your safety. If the provided plug does not fit into 
your outlet, consult an electrician for replacement of the obsolete 
outlet.

10

Protect the power cord from being walked on or pinched 
particularly at plugs, convenience receptacles, and the point 
where they exit from the apparatus.

11

Only use attachments/accessories specified by the manufacturer.

12

Use only with cart, stand, tripod, bracket, or 
table specified by the manufacturer, or sold with 
the apparatus. When a cart is used, use caution 
when moving the cart/apparatus combination 
to avoid injury from tip-over.

13

Unplug this apparatus during lightning storms or when unused 
for long periods of time.

14

Refer all servicing to qualified service personnel. Servicing is 
required when the apparatus has been damaged in any way, such 
as power-supply cord or plug is damaged, liquid has been spilled 
or objects have fallen into the apparatus, the apparatus has been 
exposed to rain or moisture, does not operate normally, or has 
been dropped.

Laser safety:

 Your TV/DVD combo uses a laser system. 

Only a qualified service person should remove the 
cover or attempt to service your TV/DVD combo 
because of possible eye injury.

Warning:

 Visible laser radiation is present when open 

and interlocks defeated. 

Do not stare into beam

. The laser is located 

inside, near the deck mechanism.

Condensation

Moisture will form in the operating section of the player if the player is 
brought from cool surroundings into a warm room or if the temperature 
of the room rises suddenly. When this happens, the DVD player's 
performance will be impaired. To prevent this, let the player stand in its 
new surroundings for about an hour before switching it on, or make 
sure that the room temperature rises gradually.
Condensation may also form during the summer if the player is exposed 
to the breeze from an air conditioner. In such cases, change the location 
of the player.

Handling the LCD panel

• Do not press hard or jolt the LCD panel. It may cause the LCD 

panel glass to break and injury may occur.

• If the LCD panel is broken, make absolutely sure that you do not 

touch the liquid in the panel. This may cause skin inflammation.

• If the liquid gets in your mouth, immediately gargle and consult 

with your doctor. Also, if the liquid gets in your eyes or touches 
your skin, consult with your doctor after rinsing for at least 15 
minutes or longer in clean water.

Damage requiring service

Unplug this TV from the power outlet and refer servicing to qualified 
service personnel under the following conditions:

• When the power supply cord or plug is damaged or frayed.
• If liquid has been spilled or objects have fallen into your 

TV/DVD combo.

• If your TV/DVD combo has been exposed to rain or water.
• If your TV/DVD combo does not operate normally by following 

the operating instructions. Adjust only those controls that are 
covered by the operating instructions because incorrect 
adjustment of other controls may result in damage and will often 
require extensive work by a qualified technician to restore your 
TV/DVD combo to its normal operation.

• If your TV/DVD combo has been dropped or damaged in any way.
• When your TV/DVD combo exhibits a distinct change in 

performance.

Replacement parts

When replacement parts are required, make sure that the service 
technician uses replacement parts specified by the manufacturer that 
have the same characteristics as the original part. Unauthorized 
substitutions may result in fire, electric shock, personal injury, or other 
hazards.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

 TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.

The lightning flash with arrowhead symbol, 
within an equilateral triangle is intended to 
alert the user to the presence of uninsulated 
dangerous voltage within the product’s 
enclosure that may be of sufficient 
magnitude to constitute a risk of electric 
shock.

The exclamation point within an equilateral 
triangle is intended to alert the user to the 
presence of important operating and 
maintenance (servicing) instructions in the 
literature accompanying the appliance.

Summary of Contents for DX-LTDVD19-09





























Reviews: