background image

J7886 D180 v1.1 

 

Page 11 of 20 

4.4  TIMES Page 

 

The Times Page is divided into three sections: 
TIME, TIMERS, and ENGINE TIMERS. 

The Flight Timer shows the total amount of time 
that oil pressure is above 15 PSI since the D180 
was turned on; it does not reset until the next time 
the D180 is power-cycled and oil pressure 
reaches 15 PSI. 

The Trip Timer shows cumulative flight time since 
a manual reset. The third line of this section 
contains the general purpose Timer which can be 
used for a variety of functions including a tank 
timer. 

The Tach Timer keeps track of engine time 
(normalized to cruise RPM). The Hobbs Timer 
records the duration of time engine oil pressure is 
at 15 PSI or higher. 

NOTE

The Hobbs Timer reading is to be noted in the 
flight log as a record of engine operation time. 

 

4.5  EMS FUEL Computer Page 

 

This page displays fuel tank levels, fuel flow, fuel 
pressure, fuel remaining, fuel used, and time 
remaining. 

NOTE

Operation of the fuel computer is not 
recommended for basic flight operations. 

Even for advanced operations, due to the 
accuracy of Jabiru fuel gauges, the fuel computer 
should not be used unless the tanks are full at the 
beginning of calculations. 

 

Summary of Contents for D180 FlightDEK





















Reviews: