GB
8
Operation: General
(Stand-By) using the button
W
on the front of the device.
If you switch the power supply off at the main switch then any stored data such as time and radio presets
will be lost.
When the power supply is switched on at the main switch (position I), the device goes into Stand-By mode.
·
Press the ON/OFF switch (Stand-By) button
W
and the device comes on. The Display
R
lights up in blue.
·
Press the ON/OFF switch (Stand-By) button
W
again to switch off the device.
·
If the device is not to be used for an extended period, pull the mains plug out of the mains socket.
Using the remote control handset
·
Point the remote control handset at the sensor
E
to achieve the best signal.
The functions of the buttons on the remote control handset are identical with those on the device.
The maximum range of the remote control signal is about 5 metres.
A strong light source in the room may adversely affect the remote control functions.
Changing the battery in the remote control handset
·
Replace the battery in the remote control handset if the device does not react appropriately to the
handset signal.
·
For this you will require a 3 volt battery CR 2025.
–
Open the battery compartment in the back of the remote control handset as described there and
remove the discharged battery
–
Insert the new battery, making sure that the polarity is correct (+ pole of the battery points upwards)
–
Close the battery compartment again
·
Avoid pressing more than one function button at a time as otherwise this could reduce the service life of
your handset.
·
If the handset is not to be used for an extended period, remove the battery from the battery compartment.
Device/ source select [ »CD/TUNER/AUX« ]
·
Press the appropriate button * to select a device or change the source:
i
CD = CD player
Y
TUNER = radio
w
AUX = external device, e.g. record deck
Adjusting Volume / Mute settings [ »VOLUME / MUTE« ]
You can adjust the volume by using the Volume control or the appropriate button on the remote control
handset. The Mute setting can be activated from the handset only.
Setting the volume at the device:
·
Turn the Volume control
P
in the VOL + direction to increase the volume. The volume setting is displayed
(increasing) for a short period in the Display
R
.
·
Turn the Volume control
P
in the VOL – direction to decrease the volume. The volume setting is displayed
(decreasing) for a short period in the Display
R
.
Adjusting the volume using the remote control handset:
·
Press the VOL + button
P
to increase the volume. The volume setting is displayed (increasing) for a short
period in the Display
R
.
·
Press the VOL – button
P
to decrease the volume. The volume setting is displayed (decreasing) for a short
period in the Display
R
.
Activating / deactivating Mute:
·
Press the Mute button
D
to activate Mute. Whilst in Mute mode the Display continuously alternates
between the operating mode (e.g. Radio mode = station frequency) and “VOL 0”.
·
Press the Mute button
D
again to deactivate Mute. The Display briefly shows “VOL ON” and then changes
back to the last operating mode (e.g. back to Radio mode).
Selecting the Tone [ »FLAT / ROCK / JAZZ / POP / CLASSIC / D-BASS« ]
Use the tone selector button
q
to set the tone quality of a track to suit the type of music and increase
listening pleasure. The current setting Rock/Jazz/Classic/Pop is shown in the display
R
-
(FLAT = neutral tone).
Note:
On model KH 2341, the Tone can be selected only using the remote control handset.
Press the D-Bass button
H
on the handset to set the Bass Boost. The Display shows D-BASS.
Headphones [ »PHONES« ]
8-32 Ohm stereo headphones
A
can be connected to the headphones connector with a 3.5 mm jack plug.
As soon as the headphones are connected the loudspeakers are turned off. Please note that high levels of
sound can lead to serious hearing damage.
Setting the time
You can set the time in Stand-By mode or by using the Timer function.
Setting the time in Stand-By mode:
1. Press the Memory button
}
once. The Hours display starts to flash.
2. Now press buttons
U
or
I
to set the Hours display. The Hours setting is shown in the Display
R
.
3. Press the Memory button
}
once more and the Minutes display starts to flash.
BA-Ident-No_2340…41-012004-1_GB 12.05.2004 12:42 Uhr Seite 8
Summary of Contents for KH 2340
Page 1: ...BA Ident No_2340 41 012004 1_D 12 05 2004 12 00 Uhr Seite 1 ...
Page 3: ...u u BA Ident No_2340 41 012004 1_D 12 05 2004 12 00 Uhr Seite 2 ...
Page 5: ...BA Ident No_2340 41 012004 1_D 12 05 2004 12 00 Uhr Seite 4 ...
Page 22: ...BA Ident No_2340 41 012004 1_GB 12 05 2004 12 42 Uhr Seite 12 ...
