background image

10

User Manual EE371 Compact Dew Point Senor

5  Electrical Connection

Important note:

  

The manufacturer cannot be held responsible for personal injuries or damage to property as a result of 

incorrect handling, installation, wiring, power supply and maintenance of the device.
The electrical connection is made via the 7-pin connector DIN VDE 0627 / IEC 61984. A mating 

connector is included in scope of supply.

1

7

6

5

2

3

4

1   V+

2   GND

3   GND

4   OUT1

5   OUT2

6   NC

7   NC

V

mA

V

mA

10...30V DC

1

7

6

5

2

3

4

1   V+

2   GND

3   NC11

4   NC12

5   NC21

6   NC22

7   not connected

10...30V DC

Analogue output

The switching thresholds are factory set:

6  Operating Components

6.1  Electronics Board

5. Display

2. Status LEDs
3. Current-/ voltage output

1. Serial interface

4. Diagnostic LED

1. Serial interface:

Connector for serial interface cable HA010304 or EE-PCA Product Configuration Adapter with 

HA011063. See data sheets EE371, Accessories and EE-PCA at www.epluse.com/ee371. 

2. Status LEDs:

Provide information on the status of the EE371. 

Green

Yellow

Red

Green (Power LED): 

flashing = EE371 is correctly powered

The yellow and red LEDs don't have any function.

Summary of Contents for EE371















Reviews: