background image

12

User Manual EE371 Compact Dew Point Senor

Adjustment

The adjustment improves the measurement accuracy of a device. The specimen is compared with the 

reference and brought in line with it. An adjustment can be followed by a calibration which documents 

the accuracy of the adjusted specimen.

The dew point temperature adjustment of EE371 can be performed with the free EE-PCS Product 

Configuration Software, free download at www.epluse.com/configurator.

7.3  Dew Point Adjustment by the User

Dew point adjustment by the user is possible only at low dew points. The adjustment can only be 

carried out if the difference between the ambient temperature and the reference dew point temperature 

is <-60 °C.

Example:

Ambient temperature = 20 °C

Reference dew point temperature must be lower than -40 °C.

8  Maintenance

8.1  Cleaning the Sensing Element

Caution:

 

ƒ

Never touch the sensing elements.

 

ƒ

Any attempt to clean the sensing elements mechanically such as rubbing or brushing leads certainly 

to their irreversible damage.

Please refer to the “Cleaning Instructions”, available online at the E+E Download-Center.

8.2  Filter Replacement

A contaminated filter cap should replaced by a new one. The order number for a new filter is HA010103.

When replacing the filter, please note the following:

 

ƒ

Unscrew the filter cap very carefully to avoid damaging the sensing element.

 

ƒ

Handling the filter might clog the pores. Use gloves to screw on the new filter.

Filter cap

Sensing element

Fig. 8 

EE371 filter and sensing elementr

8.3  Self-Diagnosis and Error Messages

Self-diagnosis via LED on the circuit board:
Power LED (green):

 

ƒ

flashing   

   EE371 is correctly powered / the microprocessor is active

 

ƒ

constantly lit   

   Electronics defect => please contact the producer

LED D1 (blue):

 

ƒ

flashing  

   The sensing element is wet (condensation)

 

ƒ

constantly lit  

   The sensing element is damaged

Self-diagnostic via display (option):

 

ƒ

Error 1  

   The dew point sensing element is damaged

 

ƒ

Error 2  

   The sensing element is wet (condensation)

 

ƒ

Error 3  

   The temperature sensing element is damaged

 

ƒ

Error 4  

   Short circuit on the temperature sensing element

Summary of Contents for EE371















Reviews: