background image

2

EN

 

WARNING:

 Read the ENTIRE instruction manual to become familiar with the features of the 

product before operating. Failure to operate the product correctly can result in damage to the product, 
personal property and cause serious injury. 

This is a sophisticated hobby product. It must be operated with caution and common sense and requires 
some basic mechanical ability. Failure to operate this product in a safe and responsible manner could 
result in injury or damage to the product or other property. This product is not intended for use by 
children without direct adult supervision. Do not use with incompatible components or alter this product 
in any way outside of the instructions provided by Horizon Hobby, Inc. This manual contains instructions 
for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings 
in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious 
injury.

Meaning of Special Language:

The following terms are used throughout the product literature to indicate various levels of potential 
harm when operating this product:

NOTICE:

 Procedures, which if not properly followed, create a possibility of physical property damage AND 

little or no possibility of injury.

CAUTION:

 Procedures, which if not properly followed, create the probability of physical property damage 

AND a possibility of serious injury.

WARNING:

 Procedures, which if not properly followed, create the probability of property damage, 

collateral damage, and serious injury OR create a high probability of superfi cial injury.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion 
of Horizon Hobby, Inc. For up-to-date product literature, visit www.horizonhobby.com and click on the 
support tab for this product.

Age Recommendation: Not for children under 
14 years. This is not a toy. 

Safety Precautions and Warnings

 

• Always keep a safe distance in all directions 

around your model to avoid collisions or injury. 
This model is controlled by a radio signal subject 
to interference from many sources outside your 
control. Interference can cause momentary loss 
of control. 

• Always operate your model in open spaces away 

from full-size vehicles, traffi c and people.

• Always carefully follow the directions and 

warnings for this and any optional support equip-
ment (chargers, rechargeable battery packs, etc.).

• Always keep all chemicals, small parts and 

anything electrical out of the reach of children.

• Always avoid water exposure to all equipment 

not specifi cally designed and protected for this 
purpose. Moisture causes damage to electronics.

• Never place any portion of the model in your 

mouth as it could cause serious injury or even 
death.

• Never operate your model with low transmitter 

batteries.

• Always keep aircraft in sight and under control.
• Always use fully charged batteries.
• Always keep transmitter powered on while 

aircraft is powered.

• Always remove batteries before disassembly.
• Always keep moving parts clean.
• Always keep parts dry.
• Always let parts cool after use before touching.
• Always remove batteries after use.
• Always ensure failsafe is properly set 

before fl ying.

• Never operate aircraft with damaged wiring.
• Never touch moving parts.

Summary of Contents for EDGE 540QQ 280




















Reviews: