Exploded View Parts Listing
Exploded View Description
Included In
Reference #
(Quantity Requested)
Item #
001
Stabilizer Flybar Paddle (2)
EFLH2219
002
Stabilizer Flybar Seesaw (1)
EFLH2219
003
Stabilizer Flybar (1)
EFLH2219
004
Upper Rotor Head & Stabilizer Flybar Hub/Holder (1) EFLH2212
005
Upper Rotor Blade (2)
EFLH2221
006
Bushing (2)
EFLH2213
007
Stabilizer Flybar Linkage (1)
EFLH2219
008
Screw T1.2x5mm (7)
EFLH2225
009
Inner Shaft (1)
EFLH2212
010
Bushing Holder (1)
EFLH2213
011
Lower Main Blade (2)
EFLH2220
012
Outer Shaft (1)
EFLH2213
013
Lower Rotor Head (1)
EFLH2217
014
Screw M1.2x2mm (3)
EFLH2225
015
Upper Swashplate (1)
EFLH2216
016
Bearing 6x10x2.5mm (1)
EFLH2216
017
Lower Swashplate (1)
EFLH2216
018
Main Motor, Right (1)
EFLH2210
019
Main Motor, Left (1)
EFLH2209
020
Outer Shaft Retaining Collar (1)
EFLH2214
021
Servo Pushrod Control Link (2)
EFLH2218
022
Servo Pushrod (2)
EFLH2218
023
Main Frame (1)
EFLH2224
ALSO BE SURE THAT THE THROTTLE TRIM IS SET TO THE MIDDLE
POSITION OR TO A POSITION THAT IS LOWER THAN THE MIDDLE.
Failure to lower the throttle stick to the lowest possible position in the event
of a crash could result in damage to the ESCs in the 5-in-1 unit, which may
require replacement of the 5-in-1 unit.
Note: Crash damage is not covered under warranty.
• Once you have gained experience and confidence in hovering the Blade
mCX, you can attempt more advanced maneuvers including:
Forward Flight
Skidding Takeoffs
Backward Flight
Skidding Landings
Pirouettes
Spot Landings
Transmitter and Receiver Binding
Binding is the process of programming the receiver to recognize the GUID
(Globally Unique Identifier) code of a single specific transmitter. If you ever
find it is necessary to replace the transmitter or the receiver/5-in-1 unit
for your model, it will be necessary for you to ‘bind’ the new transmitter
or receiver/5-in-1 to your existing transmitter or receiver/5-in-1 for proper
operation.
The following steps outline the binding process:
• Make sure the flight battery is disconnected from the 5-in-1 unit and the
transmitter is turned off.
• Plug the flight battery into the 5-in-1 unit. After 5 seconds the LED on the
5-in1 unit will begin flashing.
• PUSH directly down on the left-hand stick while switching the transmitter
on (you will feel a ‘click’ when you push in on the end of the stick).
• If you entered bind mode correctly, you will hear a series of beeps from
the transmitter and see the LED on the transmitter blink.
• You will see a solid LED approximately 5-10 seconds later on the
receiver/5-in-1. You should now be bound to the transmitter, and have full
control and function.
If you encounter any problems, repeat the binding process again or call the
Horizon Support Team at 1-877-504-0233.
26
27
Summary of Contents for EFLH2200
Page 19: ......