background image

GENERAL

1) I will not fly my model aircraft in sanctioned events, 
air shows or model flying demonstrations until it has 
been proven to be airworthy by having been previously, 
successfully flight tested.

2) I will not fly my model higher than approximately 400 
feet within 3 miles of an airport without notifying the 
airport operator. I will give right-of-way and avoid flying 
in the proximity of full-scale aircraft. Where necessary, 
an observer shall be utilized to supervise flying to avoid 
having models fly in the proximity of full-scale aircraft.

3) Where established, I will abide by the safety rules  
for the flying site I use, and I will not willfully or 
deliberately fly my models in a careless, reckless  
and/or dangerous manner.

4) The maximum takeoff weight of a model is 55 pounds, 
except models flown under Experimental Aircraft rules.

5) I will not fly my model unless it is identified with my 
name and address or AMA number on or in the model. 
(This does not apply to models while being flown indoors.)

6) I will not operate models with metal-bladed propellers 
or with gaseous boosts, in which gases other than air 
enter their internal combustion engine(s); nor will I operate 
models with extremely hazardous fuels such as those 
containing tetranitromethane or hydrazine.

RADIO CONTROL

1) I will have completed a successful radio equipment 
ground range check before the first flight of a new or 
repaired model.

2) I will not fly my model aircraft in the presence of 
spectators until I become a qualified flier, unless assisted 
by an experienced helper.

3) At all flying sites a straight or curved line(s) must be 
established in front of which all flying takes place with the 
other side for spectators. Only personnel involved with 
flying the aircraft are allowed at or in front of the flight 
line. Intentional flying behind the flight line is prohibited.

2006 Official AMA National Model Aircraft Safety Code

4

Summary of Contents for Extra 260 3D Profile













































Reviews: