background image

40

E-flite F-86 Sabre 15 DF ARF Assembly Manual

DAMAgE LIMITS

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, 

INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS 

OF PROFITS OR PRODUCTION OR COMMERCIAL 

LOSS IN ANY WAY CONNECTED WITH THE 

PRODUCT, WHETHER SUCH CLAIM IS BASED IN 

CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT 

LIABILITY. Further, in no event shall the liability of 

Horizon exceed the individual price of the Product on 

which liability is asserted. As Horizon has no control 

over use, setup, final assembly, modification or misuse, 

no liability shall be assumed nor accepted for any 

resulting damage or injury. By the act of use, setup or 

assembly, the user accepts all resulting liability.

If you as the Purchaser or user are not prepared 

to accept the liability associated with the use of 

this Product, you are advised to return this Product 

immediately in new and unused condition to the place 

of purchase.

Law: These Terms are governed by Illinois law (without 

regard to conflict of law principals). 

Warranty Services

QUESTIONS, ASSISTANCE, AND REPAIRS

Your local hobby store and/or place of purchase 

cannot provide warranty support or repair. Once 

assembly, setup or use of the Product has been 

started, you must contact Horizon directly. This will 

enable Horizon to better answer your questions 

and service you in the event that you may need any 

assistance. For questions or assistance, please direct 

your email to productsupport@horizonhobby.com, 

or call 877.504.0233 toll free to speak to a service 

technician.

INSPECTION OR REPAIRS

If this Product needs to be inspected or repaired, 

please call for a Return Merchandise Authorization 

(RMA). Pack the Product securely using a shipping 

carton. Please note that original boxes may be 

included, but are not designed to withstand the rigors 

of shipping without additional protection. Ship via a 

carrier that provides tracking and insurance for lost 

or damaged parcels, as Horizon is not responsible 

for merchandise until it arrives and is accepted at our 

facility. A Service Repair Request is available at www.

horizonhobby.com on the “Support” tab. If you do 

not have internet access, please include a letter with 

your complete name, street address, email address 

and phone number where you can be reached during 

business days, your RMA number, a list of the included 

items, method of payment for any non-warranty 

expenses and a brief summary of the problem. 

Your original sales receipt must also be included for 

warranty consideration. Be sure your name, address, 

and RMA number are clearly written on the outside of 

the shipping carton.

WARRANTy INSPECTION AND REPAIRS

To receive warranty service, you must include your 

original sales receipt verifying the proof-of-purchase 

date. Provided warranty conditions have been met, 

your Product will be repaired or replaced free of 

charge. Repair or replacement decisions are at the sole 

discretion of Horizon Hobby.

NON-WARRANTy REPAIRS

Should your repair not be covered by warranty the 

repair will be completed and payment will be required 

without notification or estimate of the expense unless 

the expense exceeds 50% of the retail purchase cost. 

By submitting the item for repair you are agreeing 

to payment of the repair without notification. Repair 

estimates are available upon request. You must include 

this request with your repair. Non-warranty repair 

estimates will be billed a minimum of 1/2 hour of 

labor. In addition you will be billed for return freight. 

Please advise us of your preferred method of payment. 

Horizon accepts money orders and cashiers checks, 

as well as Visa, MasterCard, American Express, and 

Discover cards. If you choose to pay by credit card, 

please include your credit card number and expiration 

date. Any repair left unpaid or unclaimed after 90 

days will be considered abandoned and will be 

disposed of accordingly. Please note: non-warranty 

repair is only available on electronics and model 

engines.

United States:

Electronics and engines requiring inspection or repair 

should be shipped to the following address:

Horizon Service Center

4105 Fieldstone Road

Champaign, Illinois 61822

USA

All other Products requiring warranty inspection or 

repair should be shipped to the following address:

Horizon Product Support

4105 Fieldstone Road

Champaign, Illinois 61822

USA

Please call 877-504-0233 or e-mail us at 

productsupport@horizonhobby.com with any questions 

or concerns regarding this product or warranty.

Summary of Contents for F86 Sabre 15DF













































Reviews: