background image

55

E-flite Habu 32 EDF ARF Assembly Manual

2010 Official Academy of Model 

Aeronautics Safety Code

A. GENERAL

  A model aircraft is a non-human-carrying aircraft 

capable of sustained flight in the atmosphere. It 

may not exceed limitations of this code and is 

intended exclusively for sport, recreation and/or 

competition. All model flights must be conducted 

in accordance with this safety code and any 

additional rules specific to the flying site.

1.  Model aircraft will not be flown:
  (a) In a careless or reckless manner.
  (b) At a location where model aircraft activities are 

prohibited.

2.  Model aircraft pilots will:
  (a) Yield the right of way to all man carrying 

aircraft.

  (b) See and avoid all aircraft and a spotter must be 

used when appropriate. (AMA Document #540-D-

See and Avoid Guidance.)

  (c) Not fly higher than approximately 400 feet 

above ground level within three (3) miles of an 

airport, without notifying the airport operator.

  (d) Not interfere with operations and traffic patterns 

at any airport, heliport or seaplane base except 

where there is a mixed use agreement.

  (e) Not exceed a takeoff weight, including fuel, 

of 55 pounds unless in compliance with the AMA 

Large Model Aircraft program. (AMA Document 

520-A)

  (f) Insure the aircraft is identified with the name and 

address or AMA number of the owner on the inside 

or affixed to the outside of the model aircraft.

  (This does not apply to model aircraft flown 

indoors).

  (g) Not operate aircraft with metal-blade propellers 

or with gaseous boosts except for helicopters 

operated under the provisions of AMA Document 

#555.

  (h) Not operate model aircraft while under the 

influence of alcohol or while using any drug which 

could adversely affect the pilot’s ability to safely 

control the model.

  (i) Not operate model aircraft carrying pyrotechnic 

devices which explode or burn, or any device 

which propels a projectile or drops any object that 

creates a hazard to persons or property.

Exceptions:

•  Free Flight fuses or devices that burn producing 

smoke and are securely attached to the model 

aircraft during flight.

•  Rocket motors (using solid propellant) up to a 

G-series size may be used provided they remain 

attached to the model during flight. Model rockets 

may be flown in accordance with the National 

Model Rocketry Safety Code but may not be 

launched from model aircraft.

•  Officially designated AMA Air Show Teams (AST) 

are authorized to use devices and practices as 

defined within the Team AMA Program Document 

(AMA Document #718).

  (j) Not operate a turbine-powered aircraft, unless 

in compliance with the AMA turbine regulations. 

(AMA Document #510-A).

3.  Model aircraft will not be flown in AMA sanctioned 

events, air shows or model demonstrations unless:

  (a) The aircraft, control system and pilot skills have 

successfully demonstrated all maneuvers intended or 

anticipated prior to the specific event.

  (b) An inexperienced pilot is assisted by an 

experienced pilot.

4.  When and where required by rule, helmets must be 

properly worn and fastened. They must be OSHA, 

DOT, ANSI, SNELL or NOCSAE approved or 

comply with comparable standards.

B. RADIO CONTROL (RC)

1.  All pilots shall avoid flying directly over unprotected 

people, vessels, vehicles or structures and shall 

avoid endangerment of life and property of others.

2.  A successful radio equipment ground-range check in 

accordance with manufacturer’s recommendations 

will be completed before the first flight of a new or 

repaired model aircraft.

3.  At all flying sites a safety line(s) must be established 

in front of which all flying takes place (AMA 

Document #706-Recommended Field Layout):

  (a) Only personnel associated with flying the model 

aircraft are allowed at or in front of the safety line.

  (b) At air shows or demonstrations, a straight safety 

line must be established.

  (c) An area away from the safety line must be 

maintained for spectators.

  (d) Intentional flying behind the safety line is 

prohibited.

4.  RC model aircraft must use the radio-control 

frequencies currently allowed by the Federal 

Communications Commission (FCC). Only 

individuals properly licensed by the FCC are 

authorized to operate equipment on Amateur Band 

frequencies.

5.  RC model aircraft will not operate within three 

(3) miles of any pre-existing flying site without 

a frequency-management agreement (AMA 

Documents #922- Testing for RF Interference; #923- 

Frequency Management Agreement)

6.  With the exception of events flown under official 

AMA Competition Regulations, excluding takeoff 

and landing, no powered model may be flown 

outdoors closer than 25 feet to any individual, 

except for the pilot and the pilot’s helper(s) located 

at the flight line.

7.  Under no circumstances may a pilot or other 

person touch a model aircraft in flight while it is 

still under power, except to divert it from striking an 

individual.

  This does not apply to model aircraft flown indoors.
8.  RC night flying requires a lighting system providing 

the pilot with a clear view of the model’s attitude 

and orientation at all times.

9.  The pilot of a RC model aircraft shall:
  (a) Maintain control during the entire flight, 

maintaining visual contact without enhancement 

other than by corrective lenses prescribed for the 

pilot.

  (b) Fly using the assistance of a camera or First-

Person View (FPV) only in accordance with the 

procedures outlined in AMA Document #550.

Summary of Contents for Habu 32 EDF ARF

























































Reviews: