background image

EN

13

Replacement Parts

Optional Parts

Part #

Description

EFL7750

Viper 70mm EDF BNF Basic 

EFL7775

Viper 70mm EDF PnP

EFL7701

Fuselage: Viper 70mm

EFL7702

Main Wing Set: Viper 70mm

EFL7703

Vertical Stabilizer: Viper 70mm

EFL7704

Horizontal Stabilizer: Viper70mm

EFL7705

Cockpit: Viper 70mm

EFL7706

Front Landing Gear Set:Viper70mm

EFL7707

Main Landing Gear Set: Viper70mm

EFLG7708

Front Landing GearSystem:Viper70

EFLG7709

Main Landing Gear System:Viper70

EFL7710

Landing Gear Cover: Viper 70mm

EFL7711

Linkage Rod: Viper 70mm

EFL7712

Control Horns: Viper 70mm

EFL7713

Wheel Set: Viper 70mm

EFL7714

Screw Set: Viper 70mm

EFL7715

Decal Sheet: Viper 70mm

SPMA380 

Servo: 9g digital metal gear

SPMA380R 

Servo: 9g digital metal gear 

EFLA1070EC5 

70A ESC, EC5

EFLM1850 

Motor 2860 KV1850 Yak 130

FLG130

Nose Gear Retract Mechanism

EFLG131

Main Gear Retract Mechanism

Part #

Description

SPMAR636 

AR636 6-Ch AS3X Sport Receiver

SPMR12000 

iX12 12 Channel Transmitter Only

SPMR6750 

DX6 Transmitter Only MD2 G3

SPMR8000 

DX8 Transmitter Only MD2

SPMR8100 

DX8e 8CH Transmitter Only

SPMR9910 

DX9 Black Transmitter Only MD2

Problem

Possible Cause

Solution

Control surface does 

not move

Control surface, control horn, linkage or servo damage

Replace or repair damaged parts and adjust controls

Wire damaged or connections loose

Do a check of wires and connections, connect or replace as needed

Transmitter is not bound correctly or the incorrect air-

planes was selected

Re-bind or select correct airplanes in transmitter

Flight battery charge is low

Fully recharge flight battery

BEC (Battery Elimination Circuit) of the ESC is damaged

Replace ESC

Controls reversed

Transmitter settings are reversed

Perform the Control Direction Test and adjust the controls on transmitter appropriately

Motor power pulses 

then motor loses 

power

ESC uses default soft Low Voltage Cutoff (LVC)

Recharge flight battery or replace battery that is no longer performing

Weather conditions might be too cold

Postpone flight until weather is warmer

Battery is old, worn out, or damaged

Replace battery

Battery C rating might be too small

Use recommended battery

Summary of Contents for Viper 70mm EDF


















Reviews: