1) Reset button
2) HDMI input
3) HDMI output (loopout)
4) RJ11 modular port for LAN
5) select button Powerline/LAN
6) power connection (110 - 240V AC)
1) Reset button
2) HDMI output (loopout)
3) RJ11 modular port for LAN
4) select button Powerline/LAN
5) power connection (110 - 240V AC)
Powerline / Telephoneline
HDMI Cable
Set top box
Loopout
7) LED “HDMI“
- shining = HDMI source is connected
8) LED “signal“
- shining = searching a signal
- flashing = data transfer
9) LED “power“
- shining = connected to mains power
6) LED “signal strength“
- low level, try another power or network socket
- medium level, maybe transmission is not noisefree
- high level, transmission faultless
7) LED “HDMI“
- shining = HDMI reproducer is connected
8) LED “signal“
- shining = searching a signal
- flashing = data transfer
9) LED “power“
- shining = connected to mains power
HDT 300
Quick installation guide
Elektrik Handels GmbH & Co. KG
• Am Ohrt 7 • D-59469 Ense-Höingen
Tel.: 0 29 38 - 98 76 20 • Fax: 0 29 38 - 98 76 22 2 • www.e-und-p.de
DESCRIPTION, FUNCTION AND PROPER USE
The HDT 300 transmits HDMI signals in FullHD (1920x1080p at 60Hz) via powerline or LAN, the
max. distance is 300m. A different use than the above mentioned is not allowed.
CONNECTIONS
SAFETY INSTRUCTIONS
1. Make sure all instructions in this manual are completely read and understood before you start
installation of the product.
2. Read the manual carefully and completely, it contains important notes and instructions. Keep the
manual for future reference.
3. This product is not a toy and should not be placed into the hands of children. The package contains
small parts which could be swallowed and result in suffocation or injury.
4. Do not expose the product to heat or direct sunlight. The product may only be installed and used
in dry rooms.
5. A defective product must not be used furthermore. Remove the product from the mains circuit
and secure it against further use. Repairs of defective devices must be done by especially educated
and skilled personnel.
6. The product might get warm during operation. Secure proper ventilation, do not cover the
product and do not put things on top of it.
PACKAGE CONTENT
INSTALLATION (A) - SIGNAL OVER POWERLINE
1. Make sure that all devices are switched off before starting the installation of the product.
2. Connect the HDMI output of your signal source to the transmitter (TX, input) of the HDT
300.
3. Additionally, you may connect a second TV or beamer to the transmitter (TX, loopout).
4. Connect the output of the receiver (RX, output) to the HDMI input of your TV or beamer.
5. Check the setting of the select button of transmitter and receiver both must be set to
„Power Line“.
6. Connect transmitter and receiver each to the mains power inside of the same electric cir
cuit, using the included power cables. An additional phase coupler may be used at
different phases at one counter circuit. Transmitter and receiver will sync automatically.
7. Turn on all connected devices.
8. When not in use, remove transmitter and receiver from mains circuit!
INSTALLATION (B) - SIGNAL OVER LAN
1. Make sure that all devices are switched off before starting the installation of the product.
2. Connect the HDMI output of your signal source to the transmitter (TX, input) of the HDT 300.
3. Additionally, you may connect a second TV or beamer to the transmitter (TX, loopout).
4. Connect the output of the receiver (RX, output) to the HDMI input of your TV or beamer.
5. Check the setting of the select button of transmitter and receiver: both must be set to
„Telephone Line“.
6. Connect transmitter and receiver each to a network port, using the included modular
cables.
7. Connect transmitter and receiver to the mains power. It is not necessary to connect both
at the same mains circuit while data transfer over LAN. Transmitter and receiver will sync
automatically.
8. Turn on all connected devices.
9. When not in use, remove transmitter and receiver from mains circuit!
Loopout
Input
Telephone
Line
Switch
Power
Line
Reset
1
2
3
4 5
6
7 8 9
Output
Telephone
Line
Switch
Power
Line
Reset
1
2
3 4
5
8 9
7
6
SPECIFICATIONS
HDMI Signal
up to 1080p
resolutions
480p / 576i / 720p / 1080i / 1080p
Audio
LPCM, DTS-HD, Dolby True HD
LAN cables
RJ 11
Distances
max. 300m
Power consumption
<5W
Housing metal
DISPOSAL INSTRUCTIONS acc. to ElektroG3
1. waste management of electronic and electrical equipment products
The symbol „crossed out dustbin“ signifies that you are obliged to recycle these devices separately from
unsorted municipal solid waste. The disposal over domestic waste, e.g. residual waste or yellow recycle
bin, is forbidden. Avoid any bad throw by correct disposal at specific collecting points.
2. extraction of batteries and lamps
Any batteries, accumulators or lamps which can be removed nondestructively from the legacy device
must be cleared from before disposal and must be disposed separately as batteries or lamps.
3. return possibilities of legacy devices
Legacy devices can be submitted free at the public possibilities for return or collection. A proper disposal of the
equipment is esured in this way. Under certain conditions a return to a retailer is also possible.
4. WEEE registration number
We are registered at the stiftung EAR, Nordostpark 72, 90411 Nürnberg as a distributer of electronic and electri-
cal equipment products by the registration number DE72183678.
WEEE-Richtlinie: 2002/96/EG
WEEE-Nr.: DE72183678
MISCELLANEOUS
Declaration of Conformity
With the CE sign e+p Elektrik Handels GmbH & Co. KG ensures, that this
product correspond to the standards and directives of the European regulations.
The warranty for this product does only covert he product itself. The manufacturer is not liable for
damages to persons or property damage caused by improper installation, operation or maintenance.
If any damage or fault is detected on your product, please contact your local specialist dealer.
All rights for misprints, technical changes of product, packaging or documentation reseved.
manual
HDMI Transmitter
HDMI Receiver
modular LAN cable(x2)
power connection cable (x2)
