background image

ET DC BLUE ADVANCED INSTALLER 2012.025.12.05.2014 

 

32 

www.et.co.za 

 

 

 

 

 

WARRANTY: All goods manufactured by G&C  Electronics cc T/A ET  Systems carry a  12 month  factory warranty from date 
of invoice. All goods are warranted to be  free of faulty components and  manufacturing defects. Faulty goods will be 
repaired or replaced at the sole discretion of ET  Systems free of charge.  This warranty is subject to the goods being 
returned to the premises of ET Systems. The carriage of goods is for the customer’s account. This warranty is only  valid if 
the correct installation and application of goods, as laid out in the applicable documentation accompanying  said 
goods, is adhered to. All warranty claims must be  accompanied by  the original invoice. All claims made by  the end 
user must be  directed to their respective service provider/installer.  

 

The  following conditions will disqualify this product from the warranty as laid out above. 

These conditions are non-negotiable. 

 

Any unauthorized non-manufacturer modifications to the product or components thereof. 

 

 

The  use of the ET  DC  BLUE ADVANCED  operator in heavy traffic applications such as office parks and 
residential complexes. 

 

 

The  use of the DC  BLUE ADVANCED  operator in non-weatherproof applications such as car ports.

 

 

The  following items are not included in the warranty. 

 

The battery. 

 

The  motor brushes. 

 

Damage due to the following: 

o

 

Wind and  other climatic influences such as lightning strikes.  

o

 

Water/moisture ingress. (This unit is not designed for use outdoors. I.e.  carports.  

o

 

High voltage surges on the household mains. 

o

 

Infestation i.e. Ants nesting… 

 

 

Summary of Contents for DC BLUE ADVANCED

































Reviews: