E2S BExBGL2D-P Instruction Manual Download

Page: 5 / 12

European Safety Systems Ltd.

Impress House, Mansell Road, Acton, London W3 7QH

www.e2s.com

Tel: +44 (0)208 743 8880

Document No. D210-00-401-IS

Issue 6

12-09-2022

Sheet 5 of 6

12. DC Wiring

A 6-way terminal block is provided on the DC beacon. There
are 2-off +ve, 2-off –ve, 1-off stage 2 & stage 3 terminals in
total.

Fig. 5 DC Terminals

12.1

Line Monitoring

On  BExBGL2D  DC  units,  dc  reverse  line  monitoring  can  be
used if required. All DC sounders have a blocking diode fitted
in their supply input lines. An end of line monitoring diode or
an end of line monitoring resistor can be connected across the
+ve and –ve terminals. If an end of line resistor is used it must
have  a  minimum  resistance  value  of  3k3Ω  and  a  minimum
power  rating  of  0.5  watts  or  a  minimum  resistance  value  of
500Ω and a minimum power rating of 2 watts.

The resistor must be connected directly across the +ve and -
ve terminals as shown in the following drawing. The resistor
leads should be kept as short as possible.

Fig. 6 End of Line Resistor Placement

13. Flash Rate Settings

The BExBGL2D beacons can produce different flash patterns
as shown in Table 1. The flash patterns are selected by
operation of the flash setting DIP switch on the PCB, Fig 9.

Fig. 7: DIP Switch Location

Table 1: Switch Positions for Flash Patterns

Switch

Setting

S1 Mode

S2 Mode

S3 Mode

(123456)

(DC & AC)

(DC Only)

000000

Steady High

Power

Flashing 1Hz

Flashing Triple

Strike

000001

Steady Low

Power

Flashing 1Hz

Flashing Triple

Strike

100000

Flashing 1Hz

Flashing

Double Strike

Flashing Triple

Strike

101000

Flashing 1.5Hz

Flashing 2Hz

Flashing Double

Strike

010000

Flashing 2Hz

Flashing Triple

Strike

Flashing Triple

Strike

110000

Flashing Double

Strike

Steady High

Power

Flashing Triple

Strike

001000

Flashing Triple

Strike

Flashing 2Hz

Flashing Double

Strike

Warning – high-intensity light source. Avoid
looking directly at the light source for
extended periods of time.

End of Line
Resistor

Summary of Contents for BExBGL2D-P













Search results

Summary of Contents for BExBGL2D-P

Reviews:

Related manuals for BExBGL2D-P

Brands by name

Popular brands

E2S BExBGL2D-P, Instruction Manual

Search results

Summary of Contents for BExBGL2D-P

Reviews:

Related manuals for BExBGL2D-P

Brands by name

Popular brands