background image

 

 

E2S Warning Signals

      Impress House, Mansell Road, Acton, London W3 7QH

 

www.e2s.com

 

Tel: +44 (0)208 743 8880

 

Document No. D210-00-651-IS

 

Issue 1

 

13-01-23

 

 

Sheet 5 of 13

 

 

11.2.  Line Monitoring 

 
On  BExS110D  DC  units,  dc  reverse  line  monitoring  can  be 
used if required. All DC sounders have a blocking diode fitted 
in their supply input lines. An end of line  monitoring diode or 
an  end  of  line  monitoring  resistor  can  be  connected  across 
the +ve and 

ve terminals. If an end of line resistor is used it 

must  have  a  minimum  resistance  value  of  3k3Ω  and  a 

minimum  power  rating  of  0.5 watts  or  a  minimum  resistance 
val

ue of 500Ω and a minimum power rating of 2 watts.

 

 
The resistor must be connected directly across the +ve and -
ve  terminals  as  shown  in  the following  drawing.  The  resistor 
leads should be kept as short as possible.  
 
SIL2 line monitoring module product version: see section 22 
for standard default values and product coding. See 
document D210-06-651 for associated wiring diagram. 

 

Fig. 6 End of Line Resistor Placement 

Note that the maximum forward polarity monitoring voltage is 
6V. A monitoring voltage greater than 6V may activate the 
alarm horn sounder and the 2nd or 3rd stages. 

 

 

 

 

 

 

 

 

12)  Tone Settings 

 
BExS110D-SIL sounders need to be set to one off the SIL 2 
approved tones to work correctly with the automated sounder 
check on pattern generation and signal output checks. 

 
 
Default =   
Tone 1 
 0 0 0 0 0 0 

 

(ON = 1, OFF = 0) 

Figure 7: DIP switch configuration 

 

Refer to D210-95-651-IS Tone Table for tone selection. 
 
Table  2  below  is  a  summary  of  DC:  D210-06-651  wiring 
options.

 

 

12.1.  Volume Control (None)

 

 

BExS110D-SIL sounder has no volume control, as the unit is 
monitoring its output the volume cannot be adjusted. 
 

13)  Maintenance, Overhaul & Repair 

 
Maintenance,  repair  and  overhaul  of  the  equipment  should 
only  be  carried  out  by  suitably  qualified  personnel  in 
accordance with the current relevant standards: 
 
EN60079-19 
IEC60079-19 

Explosive  atmospheres  -  Equipment  repair, 
overhaul and reclamation 
 

EN  60079-17 
IEC60079-17 

Explosive 

atmospheres 

Electrical 

installations inspection and maintenance 

 
The  acoustic  horn  is  made  out  of  ABS  plastic,  therefore  to 
avoid a possible ELECTROSTACTIC CHARGE the unit must 
only be cleaned with a damp cloth. 
 
Units  must  not  be  opened  while  an  explosive  atmosphere  is 
present. 
 
If  opening  the  unit  during  maintenance  operations  a  clean 
environment must be maintained and any dust layer removed 
prior to opening the unit. 
 

 

 

Config. 

Voltage 

Configuration Description 

Features  

Product 
Option 
Identifier 

1a 

DC 

Single Stage Configuration 

 

Line monitoring 

 

Negative Switching 

1b 

DC 

Two or Three Stage Configuration 

 

Common Positive  

 

Negative Switching 

DC 

Two or Three Stage Configuration 

 

Common Negative 

 

Customer to Set Header Pins to Positive 
Switching  

Table 2: Summary of Wiring Options. See Document D210-06-651 for DC Schematic Diagrams. 

 

Summary of Contents for BExS110D-SIL




















Reviews: