manualshive.com logo in svg

E2S D1xC1X05RDC024-D, Instruction Manual

The E2S D1xC1X05RDC024-D Instruction Manual is a comprehensive guide designed to help users set up and operate their product effectively. This manual is available for free download from 88.208.23.73:8080, ensuring easy access to all necessary information. Get the most out of your E2S D1xC1X05RDC024-D with this essential manual.

Share
Download
background image

INSTRUCTION MANUAL 

D1xC1 & D1xC2 
Alarm Horn Sounder & Strobe

 

Class II & III, Zone 20, 21 & 22

 

European Safety Systems Ltd.

   Impress House, Mansell Road, Acton, London W3 7QH

 

www.e2s.com

 

Tel: +44 (0)208 743 8880

 

Document No. D190-00-351-IS

 

Issue 1

 

21-03-2022

 

Sheet 1 of 6

 

D1xC1-R & D1xC2-R

 

D1xC1-F

 

D1xC2-F 

1) Product Table

Unit Type Code 

Nominal 

Input Voltage 

Nominal 

Input Current 

Voltage Range 

Sound 

Pressure Level dB(A) 

Max* 

Nom

.†

 

D1xC1X05RDC024-D 

24Vdc 

508mA 

20-28Vdc 

94 

90 

D1xC1X05RAC115-D 

115Vac 

200mA 

110-120Vac 50/60Hz 

D1xC1X05RAC230-D 

230Vac 

127mA 

220-240Vac 50/60Hz 

D1xC1X05FDC024-D 

24Vdc 

508mA 

20-28Vdc 

98 

94 

D1xC1X05FAC115-D 

115Vac 

200mA 

110-120Vac 50/60Hz 

D1xC1X05FAC230-D 

230Vac 

127mA 

220-240Vac 50/60Hz 

D1XC2X05RDC024-D 

24Vdc 

P2/P3: 647/1063mA 

20-28Vdc 

P2/P3 

96/98 

P2/P3 

92/94 

D1xC2X05RAC115-D 

115Vac 

P2/P3: 255/415mA 

110-120Vac 50/60Hz 

D1xC2X05RAC230-D 

230Vac 

P2/P3: 157/246mA 

220-240Vac 50/60Hz 

D1XC2X05FDC024-D 

24Vdc 

P2/P3: 647/1063mA 

20-28Vdc 

P2/P3 

106/109 

P2/P3 

103/105 

D1xC2X05FAC115-D 

115Vac 

P2/P3: 255/415mA 

110-120Vac 50/60Hz 

D1xC2X05FAC230-D 

230Vac 

P2/P3: 157/246mA 

220-240Vac 50/60Hz 

*Max = Tone 4

†

Nom. = Tone 44

The table shows the input current taken by the various sounders. 
The current levels shown above are for the 440Hz Continuous tone @ nominal input voltage. 
Nominal current at nominal voltage. 

Table 1: Electrical Ratings. 

2) Warnings

CAUTION 
TO  REDUCE  THE  RISK  OF  IGNITION  OF  HAZARDOUS 
ATMOSPHERES: 
DISCONNECT FROM SUPPLY BEFORE OPENING. 
KEEP TIGHTLY CLOSED WHEN IN OPERATION. 
WARNING 
FIT  SEALING  FITTING  IN  CONDUIT  RUNS  WITHIN  18  INCHES 
FROM ENCLOSURE. 
EQUIPMENT MUST NOT BE INSTALLED WITH THE HORN FACING 
UPWARDS OF HORIZONTAL 
DO  NOT  OPEN  WHEN  AN  EXPLOSIVE  ATMOSPHERE  IS 
PRESENT  
DO NOT OPEN WHEN ENERGISED  
POTENTIAL  ELECTROSTATIC  CHARGING  HAZARD  -  CLEAN 
ONLY WITH A DAMP CLOTH  

ATTENTION 
POUR 

REDUIRE 

LE 

RISQUE 

D’INFLAMMATION 

DES 

ATMOSPHÈRES DANGEREUSES : 
COUPER L 'ALIMENTATION AVANT OUVERTURE. 
CONSERVER FERMÉ PENDANT LE FONCIONNEMENT. 
AVERTISSEMENT 
CONDUITS DOIVENT ETRE SCELLES EN MOINS DE 18 POUCES. 
ÉQUIPEMENT  NE  DOIT PAS  ETRE INSTALLE  AVEC  LE  KLAXON 
TOURNEE VERS LE HAUT DE HORIZONTAL. 
NE PAS OUVRIR UN PRESENCE D’ATMOSPHERE EXPLOSIVE  
NE PAS OUVRIR ENERGIE  
DANGER POTENTIEL CHARGE ÉLECTROSTATIQUE - NETTOYER 
UNIQUEMENT AVEC UN CHIFFON HUMIDE  

Summary of Contents for D1xC1X05RDC024-D

















Reviews:

No comments

Related manuals for D1xC1X05RDC024-D

Valcom V-1090- BG Manual preview
V-1090- BG
Brand: Valcom Pages: 3
E2S GNExS1F Series Instruction Manual preview
GNExS1F Series
Brand: E2S Pages: 14

Brands by name

Popular brands

Load more brands