background image

31

The guarantee card is important certificate for ultimate users in guarantee service. No card 
supplied for loss, please conserve it well. 

[Instructions for Guarantee]

I. Guarantee period: 

The guarantee period lasts for 12months from the second day after machine purchase and 
invoice issuing. 

II. Guarantee scope: 

If  quality  problem  occurs  in  lifter  manufactured  by  our  company  in  normal  installation, 
operation  and  maintenance  based  upon  the  manual,  our  company  will  provide  free 
maintenance for the user according to regulations. 

III. Guarantee method: 

If the quality problem occurs in the lifter, the user can get contact with special dealer of our 
company  for  guarantee  based  upon  invoice  and  guarantee,  or  direct  contact  after-sales 
service  of  our  company.  The  company  will  provide  free  maintenance  or  replacement  for 
damaged parts in guarantee scope. 

IV. Any situation below never belongs to guarantee scope (that is charging service)

1. Beyond guarantee period.
2.  The  faults  caused  by  the  user’s  arbitrary  dismounting  and  change  or  the  operation  and 
maintenance not as per the manual.
3. Rising and falling steel wire rope, rubber tray and slide pad for the lifter.
4. The guarantee period of electronic components is beyond six months. 

V.  All  explanation  rights  in  manual  above  are  reserved  by  sales  department  of  the 
company.

Product 

model

Product No.

Invoice No. or Contract No.

User’s name

Address

Contact person, telephone

Purchase 

date

Operation 

organization

Telephone

Faults and maintenance service situation 

Maintained by

Date

Summary of Contents for MTP-9F


































Reviews: