14
AVI Slide Rev - C
Timer
ERD Rev
erse Sensor
MOTOR 15A
OPENING
TIMER
ERD CONTROL
MULTI FUNCTION
GATE STATUS
FEATURE SELECTOR
M/S PHASE
1
0
CLOSING
MASTER
OPEN RIGHT
BRAKE ON
CLOSE TIMER ON
SLAVE
OPEN LEFT
BRAKE OFF
CLOSE TIMER OFF
1
ON
2
3
4
OFF—ON
SELECT
MIN
MAX
OPEN
LIMIT
ERD OVERLOAD
OPENING CLOSING CLOSED
LIMIT
SLAVE MASTER
+ –
+ –
#9
#8
+ MAGLOCK
- 24 VDC
#5
+ ALARM
- 12 VDC
#6
REVERSE
LOOP
#2
POWER
24V
AC
#7
KEY
#3
M-FCN
#4
GND
GND
RCVR
24VAC
#1
COMM PORT
INPUT/OUTPUT
RECEIVER
ERD
M/P
RESET
1
O
N
2
ON ON STOP N/C
ON OFF CLOSE
OFF ON PHANTOM
OFF OFF EDGE SENSOR
S1 S2 FCN
COMM PORT
POWER
OPENING
TIMER
ERD CONTROL
MULTI FUNCTION
GATE STATUS
FEATURE SELECTOR
M/S PHASE
1
0
CLOSING
MASTER
OPEN RIGHT
BRAKE ON
CLOSE TIMER ON
SLAVE
OPEN LEFT
BRAKE OFF
CLOSE TIMER OFF
1
ON
2
3
4
OFF—ON
SELECT
MIN
MAX
OPEN
LIMIT
ERD OVERLOAD
OPENING CLOSING CLOSED
LIMIT
SLAVE MASTER
+ –
+ –
#9
#8
+ ALARM
- 12 VDC
#6
POWER
24V
AC
#7
COMM PORT
INPUT/OUTPUT
RESET
1
O
N
2
ON ON STOP N/C
ON OFF CLOSE
OFF ON PHANTOM
OFF OFF EDGE SENSOR
S1 S2 FCN
COMM PORT
POWER
INPUT/OUTPUT
TIMER
FEATURE SELECTOR
MASTER
OPEN RIGHT
BRAKE ON
CLOSE TIMER ON
SLAVE
OPEN LEFT
BRAKE OFF
CLOSE TIMER OFF
1
ON
23
4
OFF—ON
SELECT
MIN
MAX
O
Two-Way Adjustable Reverse Sensor / ERD Emergency Reversing Device
Close Timer for a Single or Master Operator
IMPORTANT:
The level of sensitivity has to do with the weight of the
gate and the condition of the installation. A heavier gate will require
LESS
sensitivity and a lighter gate will require
MORE
sensitivity.
Only a qualified service technician must make all adjustments to these sensors.
Proper function of reverse sensor (ERD):
When meeting an obstruction in the
CLOSING
direction, the gate will STOP, reverse direction and return to the FULL OPEN position.
When meeting an obstruction in the
OPENING
direction, the gate will STOP and reverse its direction and stop again after 4-6 inches. The gate
operator will stay in an “ERD OVERLOAD” state for 5 minutes or until manually reset (Reset button or power switch OFF/ON).
If the gate operator enters overload status two times in a row, the alarm will sound until manually reset.
When adjusting the sensors sensitivity:
TOO
sensitive - If the gate stops or reverses by itself.
NOT
sensitive enough - If the gate strikes an object
and does
NOT
stop or reverse.
Fine tune adjustment is
ONLY necessary
when stopping force
cannot be achieved
within normal reverse sensor ERD range.
Three (3) full turns sets ERD in the “Normal Range”:
•
Turn
Clockwise
for
MORE force
beyond normal range.
•
Turn
Counter-Clockwise
for
LESS force
than normal range.
The Control Board has a sensitivity adjustment for the
OPENING
direction and
CLOSING
direction of
the gate.
Both MUST be adjusted.
Adjustment must be made so that the gate stops and reverses when meeting an obstruction.
NOTE:
See page 17 for
master/slave close timer setup.
Switch #1
MUST
be
ON.
Turn the close timer
ON
(Switch #4) and adjust the
TIMER
from 1 to 60 seconds (Single operator mode).
OVERLOAD LED:
The OVERLOAD
LED warning light will light up when
the gate is heavier than normal for the
operator. During this warning, the
operator will
NOT
function properly.
CAUTION
Feature Selector #1 and #4
must be
ON
.
Less
Force
More
Force
More
Force
Less
Force
More
Sensitive
Less
Sensitive
Factory Set ERD Sensor “Fine Tune” Adjustment:
Please call Eagle Access before adjusting this sensor!
Opening
Gate
Direction
Closing
Gate
Direction
Clockwise increases close time.
ERD OVERLOAD
ERD OVER
ERD OVE
RD OVE
RD OVE
RD OVE
RD OVE
RD OV
RD OV
D OV
See page 11 for Features Selector.
E
OPENING
ERD CONTROL
CLOSING
Summary of Contents for AVI
Page 2: ...2 AVI Slide Rev C ...
Page 23: ...21 AVI Slide Rev C NOTES ...
